CY7C1371C
CY7C1373C
Document #: 38-05234 Rev. *D
Page 9 of 33
TCK
-
U4
R7
JTAG-Clock
Clock input to the JTAG circuitry. If the JTAG feature is
not being utilized, this pin must be connected to VSS. This
pin is not available on TQFP packages.
NC
16,38,39,42,
43,66,14
B1,C1,R1,
T1,T2,J3,
D4,L4,J5,
R5,T6,U6,
B7,C7,R7
A1,A11,B1,
B11,C2,C10,
H1,H3,H9,H
10,N2,N5,
N6,N7,
N10,P1,P2,
P11,R2
-
No Connects. Not internally connected to the die.
18M,36M, 72M, 144M and 288M are address expansion
pins and are not internally connected to the die.
NC / VDD
––
H2
–
Can either be left unconnected or connected to VDD.
Must not be connected to VSS.
CY7C1373C–Pin Definitions
Name
TQFP
BGA
fBGA
I/O
Description
A0, A1, A
37,36,32,33,
34,35,44,45,
46,47,48,49,
50,80,81,82,
83,84,99,
100
P4,N4,A2,
C2,R2,T2,
A3,B3,C3,
T3,A4,
A5,B5,C5,
T5,A6,C6,
R6,T6
R6,P6,A2,
A9,A10,A11,
B2,B9,B10,
P3,P4,P8,
P9,P10,R3,
R4,R8,R9,
R10,R11
Input-
Synchronous
Address Inputs used to select one of the 1M address
locations. Sampled at the rising edge of the CLK. A[1:0]
are fed to the two-bit burst counter.
BWA,BWB
93,94
G3,L5
B5,A4
Input-
Synchronous
Byte Write Select Inputs, active LOW. Qualified with WE
to conduct writes to the SRAM. Sampled on the rising
edge of CLK.
WE
88
H4
B7
Input-
Synchronous
Write Enable Input, active LOW. Sampled on the rising
edge of CLK if CEN is active LOW. This signal must be
asserted LOW to initiate a write sequence.
ADV/LD
85
B4
A8
Input-
Synchronous
Advance/Load Input. Used to advance the on-chip
address counter or load a new address. When HIGH (and
CEN is asserted LOW) the internal burst counter is
advanced. When LOW, a new address can be loaded into
the device for an access. After being deselected, ADV/LD
should be driven LOW in order to load a new address.
CLK
89
K4
B6
Input-
Clock
Clock Input. Used to capture all synchronous inputs to
the device. CLK is qualified with CEN. CLK is only recog-
nized if CEN is active LOW.
CE1
98
E4
A3
Input-
Synchronous
Chip Enable 1 Input, active LOW. Sampled on the rising
edge of CLK. Used in conjunction with CE2, and CE3 to
select/deselect the device.
CE2
97
B2
B3
Input-
Synchronous
Chip Enable 2 Input, active HIGH. Sampled on the rising
edge of CLK. Used in conjunction with CE1 and CE3 to
select/deselect the device.
CE3
92
B6
A6
Input-
Synchronous
Chip Enable 3 Input, active LOW. Sampled on the rising
edge of CLK. Used in conjunction with CE1 and CE2 to
select/deselect the device.
OE
86
F4
B8
Input-
Asynchronous
Output Enable, asynchronous input, active LOW.
Combined with the synchronous logic block inside the
device to control the direction of the I/O pins. When LOW,
the I/O pins are allowed to behave as outputs. When
deasserted HIGH, I/O pins are tri-stated, and act as input
data pins. OE is masked during the data portion of a write
sequence, during the first clock when emerging from a
deselected state, when the device has been deselected.
CY7C1371C–Pin Definitions (continued)
Name
TQFP
BGA
fBGA
I/O
Description
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
