 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
PI3DBV40 Datasheet(PDF) 3 Page - Pericom Semiconductor Corporation |
|
||||||||||||||||||||||||||||||
PI3DBV40 Datasheet(HTML) 3 Page - Pericom Semiconductor Corporation |
|
|
3 / 8 page  3 PS8709B 07/22/04 PI3DBV40 3.3V, Wide Bandwidth, 4-Channel, 2:1 Mux/DeMux Video Switch with Single Enable Notes: 1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. Dynamic Electrical Characteristics Over the Operating Range (TA=-40º to +85ºC, VCC=3.3V±10%, GND=0V) Parameter Description Test Conditions Min. Typ.(2) Max. Units XTALK Crosstalk f = 250MHz, See Fig. 2 - -27 - dB OIRR OFF Isolation f = 250MHz, See Fig. 3 - -32 - BW Bandwidth –3dB See Fig. 1, Fig. 4 - 500 - MHz Notes: 1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Guaranteed by design. 3. The bus switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interactions with the load on the driven side. Power Supply Characteristics Parameters Description Test Conditions(1) Min. Typ.(2) Max. Units ICC Quiescent Power Supply Current VCC = Max., VIN = GND or VCC - - 800 µA Notes: 1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between A and B pins at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (A & B) pins. 4. This parameter is determined by device characterization but is not production tested. 5. Measured on worst case corner pin. Capacitance (TA = 25°C, f = 1MHz) Parameters(4) Description Test Conditions Typ. Max. Units CIN Input Capacitance VIN = 0V 3.1 3.6 pF COFF Port I Capacitance, Switch OFF 2.8 6.0 CON Switch Capacitance, Switch ON 9.5(5) 10.9 Switching Characteristics Paramenter Description Min. Typ.(2) Max. Units tPD Propagation Delay(2,3) - 0.25 ns tPZH, tPZL Line Enable Time - SEL to YN, IN 0.5 - 15 tPHZ, tPLZ Line Disable Time - SEL to YN, IN 0.5 - 9 tSK(o) Output Skew between center port (Y4 to Y5) to any other port(2) - 0.1 0.2 tSK(p) Skew between opposite transitions of the same output (tPHL - tPLH) (2) - 0.1 0.2 |
Similar Part No. - PI3DBV40 |
|
Similar Description - PI3DBV40 |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
