Electronic Components Datasheet Search |
|
XRT8010 Datasheet(PDF) 7 Page - Exar Corporation |
|
XRT8010 Datasheet(HTML) 7 Page - Exar Corporation |
7 / 13 page XRT8010 REV. 1.0.2 312MHZCLOCK&CRYSTAL MULTIPLIERWITHLVDSOUTPUTS 6 1.0 CALIBRATION The XRT8010 synthesizer jitter performance is optimized by calibration of its Voltage Controlled Oscillator (VCO) upon initial power application. This power ON calibration procedure is automatic and completely trans- parent to the user. It is initiated automatically upon first application of VDD. In order to bring the center fre- quency of the VCO close to the desired output frequency, the VCO bias current is adjusted via a current DAC at initial power application. The center frequency of VCO is checked against input reference frequency and cal- ibrated internally to the desired output frequency value. These bias voltage trim bits are then held in latches for as long as the VDD is held above 2.7V (minimum specified operational value of VDD). The user should note the following important facts about this calibration procedure for proper operation of the XRT8010: • For proper operation of the chip and to achieve lowest jitter, the user should follow layout guidelines as described in the User Guide. • An input crystal of appropriate frequency should be connected at XTAL1 and XTAL2 pins before power is applied to the chip. • All VDD pins should be tied to 3.3V ±10% simultaneously. • The power supply should turn on without bouncing below 2.0V smoothly to its specified value in no more than 50msec. • The calibration takes place during VDD ramp up between 2.6V to 3V values. Once the VDD reaches and maintains 3.0V, the chip retains the calibrated VCO bias voltages in internal latches for proper operation. • To change a widely different value of crystal or input reference frequency, it is recommended to power down the chip by bringing VDD to 0V and restarting after the change in frequency has occurred. 2.0 CRYSTAL SELECTION It is recommended that a Fundamental Mode Crystal be used as the timing reference of the XRT8010. The fol- lowing part has been qualified by EXAR: CITIZEN Quartz Crystals 20 MHz : HCM49-20.000MABJT 40 MHz : HCM49-40.000MABJT 3.0 DATA AND PLOTS All plots were recorded using the following parameters and test setup: • VDD = 3.3 V • 2” 100 Ω Differential Transmission Lines (from LVDS outputs to receiver inputs) • Fundamental Mode Crystal of 20 MHz • Vref = 1.5 V (PECL Receiver) TABLE 3: POWER-DOWN AND OUTPUT TRI-STATE SELECTION TABLE PD PIN 8OE PIN 7STATUS NOTES 1 X Outputs tri-stated and chip Powered-down “X” = don't care 0 1 Output tri-stated PD and OE have a 50K Ω pull-down resistor to ground on chip |
Similar Part No. - XRT8010 |
|
Similar Description - XRT8010 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |