Electronic Components Datasheet Search |
|
LP2992ILDX-3.3 Datasheet(PDF) 5 Page - National Semiconductor (TI) |
|
|
LP2992ILDX-3.3 Datasheet(HTML) 5 Page - National Semiconductor (TI) |
5 / 15 page Electrical Characteristics (Continued) Limits in standard typeface are for T J = 25˚C. and limits in boldface type apply over the full operating temperature range. Un- less otherwise specified: V IN =VO(NOM) + 1V, IL = 1 mA, CIN = 1 µF, COUT = 4.7 µF, VON/OFF = 2V. Symbol Parameter Conditions Typ LP2992AI-X.X LP2992I-X.X Units (Note 6) (Note 6) Min Max Min Max I ON/OFF ON/OFF Input Current V ON/OFF = 0 0.01 −2 −2 µA V ON/OFF =5V 5 15 15 e n Output Noise BW = 300 Hz to 50 kHz, Voltage (RMS) C OUT =10µF 30 µV C BYPASS =10nF Ripple Rejection f = 1 kHz, C BYPASS =10nF 45 dB C OUT =10µF I O(SC) Short Circuit Current R L = 0 (Steady State) 400 mA (Note 9) I O(PK) Peak Output Current V OUT ≥ V o(NOM) −5% 350 mA Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the device outside of its rated operating conditions. Note 2: The ESD rating of pins 3 and 4 for the SOT-23 package, or pins 1 and 3 for the LLP package, is 1 kV. Note 3: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, θJ-A, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperture is calculated using: Where the value of θJ-A for the SOT-23 package is 220˚C/W in a typical PC board mounting and the LLP package is 65˚C/W. Exceeding the maximum allowable dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Note 4: If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2992 output must be diode-clamped to ground. Note 5: The output PNP structure contains a diode between the VIN to VOUT terminals that is normally reverse-biased. Reversing the polarity from VIN to VOUT will turn on this diode. Note 6: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate National’s Average Outgoing Quality Level (AOQL). Note 7: VIN must be the greater of 2.2V or VOUT(nom) + Dropout Voltage to maintain output regulation. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below the value measured with a 1V differential. Note 8: The ON/OFF input must be properly driven to prevent possible misoperation. For details, refer to Application Hints. Note 9: The LP2992 has foldback current limiting which allows a high peak current when VOUT > 0.5V, and then reduces the maximum output current as VOUT is forced to ground (see Typical Performance Characteristics curves). www.national.com 5 |
Similar Part No. - LP2992ILDX-3.3 |
|
Similar Description - LP2992ILDX-3.3 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |