408-10089 datasheet(2/6 Pages) MACOM | These kits were designed for use with the AMPOMATOR System III Lead?밠aking Machine and the AMP?밢?밚ECTRIC Servo Terminator III Machine.

Part No.	408-10089

Description	These kits were designed for use with the AMPOMATOR System III Lead?밠aking Machine and the AMP?밢?밚ECTRIC Servo Terminator III Machine.

Download	6 Pages

Scroll/Zoom	100%

Manufacturer	MACOM [Tyco Electronics]

Direct Link	http://www.macom.com

Logo

2 / 6 page

408-10089

Air Feed Kit 1752470-[ ] and Quick-Disconnect Kit 1752471-[ ]

Rev B

2 of 6

Tyco Electronics Corporation

Figure 2

2. Feed both the pneumatic tubing and the control

line through the slot in the front wall of the base.

(Refer to Figure 2.)

3. Remove a blanking plug from one branch of the

quick release “Y” connector.

4. Using the provided pneumatic tubing, make the

required connection to the “Y” connector.

5. Connect the control connector to the 2 position

connector in the terminator base.

6. Use the provided hardware to mount the valve

to the terminator base (Figure 3).

Figure 3

Air Feed

Valve

Contact Carrier

Cutter Valve

Be sure to position the provided washer behind the

valve on the lower screw. (See Figure 3) and

secure the control line in the provided“P–clip.”

If the optional contact carrier cutter valve is also

installed, position the air feed valve underneath

as shown in Figure 3.

3.2. Quick-Disconnect Kit Installation

Optional Quick–Disconnect Kit 1752471–1 easily

installs by pushing the provided pneumatic tubes into

the fittings on the actuating valve. See Figure 4.

To install the 1752471–2 kit, repeat the procedure for

the –1 assembly. In addition, add the “T” fitting and

quick disconnect extension as shown in Figure 5.

Figure 4

Figure 5

NOTE

i

Similar Part No. - 408-10089

Manufacturer	Part No.	Datasheet	Description
Tyco Electronics	408-10002	245Kb / 5P	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
Tyco Electronics	408-10004	3Mb / 9P	The pneumatic crimping heads consist of integral jaws which close in an arc-like motion
TE Connectivity Ltd	408-10020	126Kb / 3P	Extraction/Lance Reset Tool
Tyco Electronics	408-10021	530Kb / 5P	The CERTI--CRIMP II Tool Holder Assembly
Tyco Electronics	408-10022	91Kb / 2P	Die Assembly

More results

Similar Description - 408-10089

Manufacturer	Part No.	Datasheet	Description
Tyco Electronics	408-8022	205Kb / 4P	Read the following instructions carefully before and during the installation of the conversion kits on the machine.
Bel Fuse Inc.	MTT-300	793Kb / 2P	Solutions for the Heavy Duty Machine Industry
Tyco Electronics	408-8980	897Kb / 8P	These instructions cover the installation and use of the kits listed in the table in Figure 1.
A-Data Technology	HD710A	425Kb / 2P	Designed for Mac-supports Time Machine
Molex Electronics Ltd.	0623006100	30Kb / 1P	RAST 5.0 Power Semi-Automatic Terminator Machine for 12 and 16 AMP
Molex Electronics Ltd.	0623006300	30Kb / 1P	RAST 5.0 Power Semi-Automatic Terminator Machine for 6 and 10 AMP
Agilent(Hewlett-Packard...	5067-1511	217Kb / 2P	Kits and Reagents for the Agilent 2100 Bioanalyzer System
Bourns Electronic Solut...	TIP31B-S	142Kb / 4P	Designed for Complementary Use with the TIP32 Series
	TIP35-S	109Kb / 4P	Designed for Complementary Use with the TIP36 Series
	BD545C-S	104Kb / 4P	Designed for Complementary Use with the BD546 Series

More results

408-10089 Datasheet(PDF) 2 Page - Tyco Electronics

408-10089 Datasheet(HTML) 2 Page - Tyco Electronics

Similar Part No. - 408-10089

Similar Description - 408-10089

Html Pages

1 2 3 4 5 6

Datasheet Download

Link URL