Electronic Components Datasheet Search |
|
994916-1 Datasheet(PDF) 1 Page - TE Connectivity Ltd |
|
994916-1 Datasheet(HTML) 1 Page - TE Connectivity Ltd |
1 / 3 page ©2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company All Rights Reserved *Trademark TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks of their respective owners. 1 of 3 Instruction Sheet TOOLING ASSISTANCE CENTER 1-800-722-1111 PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com 408-8340 180° Cable Clamp Assembly 1424035-1 24 MAY 12 Rev B Figure 1 1. INTRODUCTION The 180° Cable Clamp Assembly 1424035-1 is designed to be used in CHAMPOMATOR* 2.5 Bench Terminating Machine 762734-[ ]. The machine must be equipped with a clamp solenoid valve (shown in Figure 4) and a controller having software at Rev. 3.03.05 or later. To use the machine without these requirements, use 180° Cable Clamp Assembly 768830-1 and follow the instructions packaged with that cable clamp. The cable clamp permits the machine to apply discrete-wire jacketed cable to AMPLIMITE* .050 Series connectors, AMPLIMITE HDE connectors, CHAMP* connectors, and AMPMODU* MT connectors. All dimensions on this sheet are in millimeters [with inch equivalents in brackets]. Figures and illustrations are for identification only and are not drawn to scale. Make sure to retain all material in the bench terminating machine documentation package for reference. For detailed information on the operation of the machine, refer to Customer Manual 409-5839 which is supplied with the machine. Reasons for reissue of this instruction sheet are provided in Section 8, REVISION SUMMARY. 2. DESCRIPTION (Figure 1) The cable clamp is capable of being adjusted to give a 1805 cable breakout, and it can also be offset for the angle-exit option when applying AMPLIMITE .050 Series connectors with the machine. During operation, the operator places the cable into the cable clamp, and places the wires in the wire holder, which holds the cable wires in place during the termination process, helping to keep the loose wires out of the operator's way. As the wires are terminated, the clamp follows the cam track and moves to provide the desired breakout length. The clamp eventually bottoms in the cam track, determining the position of the cable with respect to the connector. After all terminations have been completed, the machine moves to the forward home position. At this time, the operator unclamps the cable, then presses the machine's “INDEX” and “LOAD” buttons. The machine carriage and cable clamp then move to their respective home positions, permitting the operator to remove the completed cable assembly from the machine. Make sure that the cable assembly does not get caught on the cable clamp, or damage to the cable assembly could result. This is particularly important when processing the second-end connector on a short cable assembly. Cam Track Cam Air-Activated Cylinder Fitting Jaw Cable Clamp Bracket Indicator Wire Holder Clamp Bracket NOTE i NOTE i ! CAUTION |
Similar Part No. - 994916-1 |
|
Similar Description - 994916-1 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |