Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.COM

X  

1--21048--0 Datasheet(PDF) 1 Page - Tyco Electronics

Part # 1--21048--0
Description  Pneumatic Head Assembly
Download  5 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  MACOM [Tyco Electronics]
Direct Link  http://www.macom.com
Logo MACOM - Tyco Electronics

1--21048--0 Datasheet(HTML) 1 Page - Tyco Electronics

  1--21048--0 Datasheet HTML 1Page - Tyco Electronics 1--21048--0 Datasheet HTML 2Page - Tyco Electronics 1--21048--0 Datasheet HTML 3Page - Tyco Electronics 1--21048--0 Datasheet HTML 4Page - Tyco Electronics 1--21048--0 Datasheet HTML 5Page - Tyco Electronics  
Zoom Inzoom in Zoom Outzoom out
 1 / 5 page
background image
Instruction Sheet
Pneumatic Head Assembly 679304-1
408--4070
LOC B
1
of 5
E
2010 Tyco Electronics Corporation, Berwyn, PA
All Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products names, logos, or company names might be trademarks of their respective owners.
TOOLING ASSISTANCE CENTER 1-- 800-- 722-- 1111
PRODUCT INFORMATION 1-- 800-- 522-- 6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
17 MAR 10 Rev D
(For Use with 626 Pneumatic Tooling Assemblies)
Figure 1
Quick Pin 354425--1
(Qty: 2)
Tool Holder Assembly
189767--1 (Ref)
Pneumatic Head
Assembly
1. INTRODUCTION
Pneumatic Head Assembly 679304--1 (shown in
Figure 1) is designed to accept interchangeable die
assemblies used in PRO--CRIMPER* hand tools for
crimping various types of connectors. The head
assembly is used in the 626 Pneumatic Tooling
Assemblies 189721--1 and 189722--1.
This instruction sheet provides recommended
procedures for die installation and removal, crimp
head installation and removal, basic crimping
procedures, and maintenance and inspection. For
specific information concerning cable preparation and
crimping procedures, refer to the instruction sheet
packaged with the appropriate die set.
Reasons for reissue of this instruction sheet are
provided in Section 6, REVISION SUMMARY.
2. INSTALLATION AND REMOVAL
2.1. Die Assembly
Remove the head assembly from the tool holder
assembly; then remove the two pan head screws and
bushings from the jaws of the head assembly.
Install the appropriate die assembly according to the
following:
A. Shouldered Dies (See Figure 2)
1. Open the jaws of the head assembly by
squeezing the rollers together. Place the anvil die
into the jaw.
2. Slide the bushing over the pan head screw and
insert the pan head screw through the head
assembly jaw and anvil die. Tighten the screw just
enough to hold the die in place.
The die assembly shown in Figure 2 has center
contact crimping chambers and is installed with
the crimping chambers positioned toward the
front of the head assembly. If shown otherwise in
other instruction sheets, follow the die installation
requirements for the specific application.
3. Place the crimper die into the jaw of the head
assembly as shown in Figure 2.
4. Slide bushing over pan head screw and insert
pan head screw through the head assembly jaw
and crimper die. Tighten screw just enough to hold
the die in place.
NOTE
i


Similar Part No. - 1--21048--0

ManufacturerPart #DatasheetDescription
logo
Tyco Electronics
1--21046--3 MACOM-1--21046--3 Datasheet
94Kb / 3P
   Crimping Die Assemblies
More results

Similar Description - 1--21048--0

ManufacturerPart #DatasheetDescription
logo
TE Connectivity Ltd
408-8878 TEC-408-8878 Datasheet
217Kb / 4P
   626 Pneumatic Crimping Head 1490191-1 (Used with 626 Pneumatic Tooling Assemblies)
logo
Tyco Electronics
408-4198 MACOM-408-4198 Datasheet
378Kb / 6P
   This instruction sheet covers the application and maintenance procedures for Pneumatic Crimping Head Assembly
logo
TE Connectivity Ltd
408-6789 TEC-408-6789 Datasheet
268Kb / 5P
   Pistol Grip Pneumatic Handle Assembly
logo
Molex Electronics Ltd.
64007-7100 MOLEX11-64007-7100 Datasheet
29Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
0640056600 MOLEX11-0640056600 Datasheet
30Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
0640071200 MOLEX11-0640071200 Datasheet
29Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
0640050400 MOLEX11-0640050400 Datasheet
41Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
0640053600 MOLEX-0640053600 Datasheet
40Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
11/02/2021
0640054600 MOLEX-0640054600 Datasheet
40Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
11/02/2021
0640052100 MOLEX-0640052100 Datasheet
44Kb / 2P
   Crimp Head for the AT-200 Pneumatic Hand Tool
11/02/2021
More results


Html Pages

1 2 3 4 5


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com