FEDL7066-01

ML7066

8/29

List of Command/Event

The following table shows the command/event specifications of ML7066. Command is send from MCU to the ML7066.

Event is send from the ML7066 to MCU.

Command/event name

Type

code

Function

SET_TRX_STATE.request

Command

0x02

Requests the RF state change

SET_TRX_STATE.confirm

Event

0x03

Reports the result of RF state change request

SET_CHANNEL.request

Command

0x04

Sets the operating channel

SET_CHANNEL.confirm

Event

0x05

Reports the channel setting result

SET_CMP_DATA.request

Command

0x06

Sets the preamble or start-of-frame delimiter (SFD) pattern

for generation (TX) and comparison (RX)

SET_CMP_DATA.confirm

Event

0x07

Reports the preamble/SFD pattern setting result

SET_RSSI_SETTING.request

Command

0x08

Sets the carrier detect condition

SET_RSSI_SEETING.confirm

Event

0x09

Reports the carrier detect condition setting result

SET_TX_POW.request

Command

0x0a

Sets the transmitting power

SET_TX_POW.confirm

Event

0x0b

Reports the transmitting power setting result

SET_TIMER.request

Command

0x0c

Sets the intermitting operation timing

SET_TIMER.confirm

Event

0x0d

Reports the intermittent operation setting result

SET_PLL_FIT.request

Command

0x0e

Adjusts the operating channel center frequency

SET_PLL_FIT.confirm

Event

0x0f

Reports the result of frequency adjustment request

SET_TEST.request

Command

0x10

Sets the test pattern

SET_TEST.confirm

Event

0x11

Reports the result of test pattern setting results

SET_CLK.request

Command

0x12

Requests the sleep mode operation and POWOFF pin

polarity change.

SET_CLK.confirm

Event

0x13

Reports the result of sleep and POWOFF pin polarity

request

SET_RESET.request

Command

0x14

Request the reset operation

SET_RESET.confirm

Event

0x15

Reports the result of reset request

SET_CONFIRM.request

Command

0x16

Requests the interrupt masking

SET_CONFIRM.confirm

Event

0x17

Reports the interrupt mask requests

SET_INT.request

Command

0x18

Requests the .confirm event masking

SET_INT.confirm

Event

0x19

Reports the result of .confirm event mask requests

SET_SPD.request

Command

0x18

Sets the data rate

SET_SPD.confirm

Event

0x19

Reports the data rate setting request

SET_CMP_DURATION.request

Command

0x0e

Sets the comparing receive data period

SET_CMP_DURATION.confirm

Event

0x0f

Reports the comparing period setting result

RX_DATA.indication

Event

0x20

Notices existing receive data

RSSI.indication

Event

0x21

Notices RSSI result

GET_TRX_STATE.request

Command

0x22

Reads the RF state report

GET_TRX_STATE.confirm

Event

0x23

Reports the current RF state

GET_CHANNEL.request

Command

0x24

Reads the channel setting

GET_CHANNEL.confirm

Event

0x25

Reports the setting operation channel(s)

GET_CMP_DATA.request

Command

0x26

Reads the setting of the preamble or SFD pattern

GET_CMP_DATA.confirm

Event

0x27

Reports the setting pattern of preamble or SFD

GET_RSSI_SETTING.request

Command

0x28

Reads the carrier detect setting or current RSSI

GET_RSSI_SEETING.confirm

Event

0x29

Reports the carrier detect setting or current RSSI

GET_TX_POW.request

Command

0x2a

Reads the transmitting power setting

GET_TX_POW.confirm

Event

0x2b

Reports the setting value of transmitting power

GET_TIMER.request

Command

0x2c

Reads the intermitting operation timing

GET_TIMER.confirm

Event

0x2d

Reports the setting value of intermittent operation

GET_PLL_FIT.request

Command

0x2e

Reads the PLL adjust value

GET_PLL_FIT.confirm

Event

0x2f

Reports the setting value for PLL adjustment