Electronic Components Datasheet Search |
|
RV7-1212S15A1 Datasheet(PDF) 2 Page - RSG Electronic Components GmbH |
|
RV7-1212S15A1 Datasheet(HTML) 2 Page - RSG Electronic Components GmbH |
2 / 4 page RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page2(4) +Vout +Vin DC/DC Converter -Vin -Vout NOTE 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with a 1.0uF ceramic capacitor and 10uF tantalum capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Measured Input reflected ripple current with a simulated source inductance of 12uH and a source capacitor Cin (47uF, ESR<1.0© at 100KHz). 6. The remote on/off control pin is referenced to -Vin(pin2). 7. Input filter components (C1, C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. 8. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 9. Nature Convection" is usually about 30-65 LFM but is not equal to still air (0 LFM). 10 .Exceeding the absolute ratings of the unit could cause damage. It is not for continuous operating L Load C1 C2 MODEL SELECTION GUIDE NODEL NUNBER INPUT Voltage Range (Vdc ) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Nin. load (mA) Full load (mA) RV7-1203S15A1 9-18 20 1310 3.3 0 4000 85 1000 RV7-1205S15A1 9-18 20 1471 5 0 3000 86 1000 RV7-1212S15A1 9-18 20 1494 12 0 1300 88 330 RV7-1215S15A1 9-18 20 1420 15 0 1000 89 220 RV7-2403S15A1 18-36 15 647 3.3 0 4000 86 1000 RV7-2405S15A1 18-36 15 727 5 0 3000 87 1000 RV7-2412S15A1 18-36 15 747 12 0 1300 88 330 RV7-2415S15A1 18-36 15 710 15 0 1000 89 220 RV7-4803S15A1 36-75 10 327 3.3 0 4000 85 1000 RV7-4805S15A1 36-75 10 368 5 0 3000 86 1000 RV7-4812S15A1 36-75 10 374 12 0 1300 88 330 RV7-4815S15A1 36-75 10 359 15 0 1000 88 220 RV7-1205D15A1 9-18 20 1488 ± 5 0 ± 1500 85 ± 470 RV7-1212D15A1 9-18 20 1420 ± 12 0 ± 625 89 ± 220 RV7-1215D15A1 9-18 20 1437 ± 15 0 ± 500 89 ± 100 RV7-2405D15A1 18-36 15 744 ± 5 0 ±1500 85 ±470 RV7-2412D15A1 18-36 15 718 ±12 0 ±625 88 ±220 RV7-2415D15A1 18-36 15 710 ± 15 0 ± 500 89 ± 100 RV7-4805D15A1 36-75 10 377 ± 5 0 ± 1500 84 ± 470 RV7-4812D15A1 36-75 10 363 ± 12 0 ± 625 87 ± 220 RV7-4815D15A1 36-75 10 359 ±15 0 ±500 88 ±100 NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg-electronic.de C1 L C2 RV7-12XXX15A1 1210,2.2uF/100V 12uH 1210,2.2uF/100V RV7-24XXX15A1 1210,2.2uF/100V 12uH 1210,2.2uF/100V RV7-48XXX15A1 1210,2.2uF/100V 12uH 1210,2.2uF/100V +Vout +Vin DC/DC Converter -Vin -Vout NOTE 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with a 1.0uF ceramic capacitor and 10uF tantalum capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Measured Input reflected ripple current with a simulated source inductance of 12uH and a source capacitor Cin (47uF, ESR<1.0© at 100KHz). 6. The remote on/off control pin is referenced to -Vin(pin2). 7. Input filter components (C1, C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. 8. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 9. Nature Convection" is usually about 30-65 LFM but is not equal to still air (0 LFM). 10 .Exceeding the absolute ratings of the unit could cause damage. It is not for continuous operating L Load C1 C2 MODEL SELECTION GUIDE NODEL NUNBER INPUT Voltage Range (Vdc ) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Nin. load (mA) Full load (mA) RV7-1203S15A1 9-18 20 1310 3.3 0 4000 85 1000 RV7-1205S15A1 9-18 20 1471 5 0 3000 86 1000 RV7-1212S15A1 9-18 20 1494 12 0 1300 88 330 RV7-1215S15A1 9-18 20 1420 15 0 1000 89 220 RV7-2403S15A1 18-36 15 647 3.3 0 4000 86 1000 RV7-2405S15A1 18-36 15 727 5 0 3000 87 1000 RV7-2412S15A1 18-36 15 747 12 0 1300 88 330 RV7-2415S15A1 18-36 15 710 15 0 1000 89 220 RV7-4803S15A1 36-75 10 327 3.3 0 4000 85 1000 RV7-4805S15A1 36-75 10 368 5 0 3000 86 1000 RV7-4812S15A1 36-75 10 374 12 0 1300 88 330 RV7-4815S15A1 36-75 10 359 15 0 1000 88 220 RV7-1205D15A1 9-18 20 1488 ± 5 0 ± 1500 85 ± 470 RV7-1212D15A1 9-18 20 1420 ± 12 0 ± 625 89 ± 220 RV7-1215D15A1 9-18 20 1437 ± 15 0 ± 500 89 ± 100 RV7-2405D15A1 18-36 15 744 ± 5 0 ±1500 85 ±470 RV7-2412D15A1 18-36 15 718 ±12 0 ±625 88 ±220 RV7-2415D15A1 18-36 15 710 ± 15 0 ± 500 89 ± 100 RV7-4805D15A1 36-75 10 377 ± 5 0 ± 1500 84 ± 470 RV7-4812D15A1 36-75 10 363 ± 12 0 ± 625 87 ± 220 RV7-4815D15A1 36-75 10 359 ±15 0 ±500 88 ±100 NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg-electronic.de C1 L C2 RV7-12XXX15A1 1210,2.2uF/100V 12uH 1210,2.2uF/100V RV7-24XXX15A1 1210,2.2uF/100V 12uH 1210,2.2uF/100V RV7-48XXX15A1 1210,2.2uF/100V 12uH 1210,2.2uF/100V +Vout +Vin DC/DC Converter -Vin -Vout NOTE 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with a 1.0uF ceramic capacitor and 10uF tantalum capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Measured Input reflected ripple current with a simulated source inductance of 12uH and a source capacitor Cin (47uF, ESR<1.0© at 100KHz). 6. The remote on/off control pin is referenced to -Vin(pin2). 7. Input filter components (C1, C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. 8. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 9. Nature Convection" is usually about 30-65 LFM but is not equal to still air (0 LFM). 10 .Exceeding the absolute ratings of the unit could cause damage. It is not for continuous operating L Load C1 C2 MODEL SELECTION GUIDE NODEL NUNBER INPUT Voltage Range (Vdc ) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Nin. load (mA) Full load (mA) RV7-1203S15A1 9-18 20 1310 3.3 0 4000 85 1000 RV7-1205S15A1 9-18 20 1471 5 0 3000 86 1000 RV7-1212S15A1 9-18 20 1494 12 0 1300 88 330 RV7-1215S15A1 9-18 20 1420 15 0 1000 89 220 RV7-2403S15A1 18-36 15 647 3.3 0 4000 86 1000 RV7-2405S15A1 18-36 15 727 5 0 3000 87 1000 RV7-2412S15A1 18-36 15 747 12 0 1300 88 330 RV7-2415S15A1 18-36 15 710 15 0 1000 89 220 RV7-4803S15A1 36-75 10 327 3.3 0 4000 85 1000 RV7-4805S15A1 36-75 10 368 5 0 3000 86 1000 RV7-4812S15A1 36-75 10 374 12 0 1300 88 330 RV7-4815S15A1 36-75 10 359 15 0 1000 88 220 RV7-1205D15A1 9-18 20 1488 ± 5 0 ± 1500 85 ± 470 RV7-1212D15A1 9-18 20 1420 ± 12 0 ± 625 89 ± 220 RV7-1215D15A1 9-18 20 1437 ± 15 0 ± 500 89 ± 100 RV7-2405D15A1 18-36 15 744 ± 5 0 ±1500 85 ±470 RV7-2412D15A1 18-36 15 718 ±12 0 ±625 88 ±220 RV7-2415D15A1 18-36 15 710 ± 15 0 ± 500 89 ± 100 RV7-4805D15A1 36-75 10 377 ± 5 0 ± 1500 84 ± 470 RV7-4812D15A1 36-75 10 363 ± 12 0 ± 625 87 ± 220 RV7-4815D15A1 36-75 10 359 ±15 0 ±500 88 ±100 NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg-electronic.de C1 L C2 RV7-12XXX15A1 1210,2.2uF/100V 12uH 1210,2.2uF/100V RV7-24XXX15A1 1210,2.2uF/100V 12uH 1210,2.2uF/100V RV7-48XXX15A1 1210,2.2uF/100V 12uH 1210,2.2uF/100V DC/DC-Converter 15W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! +Vout +Vin DC/DC Converter -Vin -Vout NOTE 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with a 1.0uF ceramic capacitor and 10uF tantalum capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Measured Input reflected ripple current with a simulated source inductance of 12uH and a source capacitor Cin (47uF, ESR<1.0© at 100KHz). 6. The remote on/off control pin is referenced to -Vin(pin2). 7. Input filter components (C1, C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. 8. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 9. Nature Convection" is usually about 30-65 LFM but is not equal to still air (0 LFM). 10 .Exceeding the absolute ratings of the unit could cause damage. It is not for continuous operating L Load C1 C2 MODEL SELECTION GUIDE NODEL NUNBER INPUT Voltage Range (Vdc ) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Nin. load (mA) Full load (mA) RV7-1203S15A1 9-18 20 1310 3.3 0 4000 85 1000 RV7-1205S15A1 9-18 20 1471 5 0 3000 86 1000 RV7-1212S15A1 9-18 20 1494 12 0 1300 88 330 RV7-1215S15A1 9-18 20 1420 15 0 1000 89 220 RV7-2403S15A1 18-36 15 647 3.3 0 4000 86 1000 RV7-2405S15A1 18-36 15 727 5 0 3000 87 1000 RV7-2412S15A1 18-36 15 747 12 0 1300 88 330 RV7-2415S15A1 18-36 15 710 15 0 1000 89 220 RV7-4803S15A1 36-75 10 327 3.3 0 4000 85 1000 RV7-4805S15A1 36-75 10 368 5 0 3000 86 1000 RV7-4812S15A1 36-75 10 374 12 0 1300 88 330 RV7-4815S15A1 36-75 10 359 15 0 1000 88 220 RV7-1205D15A1 9-18 20 1488 ± 5 0 ± 1500 85 ± 470 RV7-1212D15A1 9-18 20 1420 ± 12 0 ± 625 89 ± 220 RV7-1215D15A1 9-18 20 1437 ± 15 0 ± 500 89 ± 100 RV7-2405D15A1 18-36 15 744 ± 5 0 ±1500 85 ±470 RV7-2412D15A1 18-36 15 718 ±12 0 ±625 88 ±220 RV7-2415D15A1 18-36 15 710 ± 15 0 ± 500 89 ± 100 RV7-4805D15A1 36-75 10 377 ± 5 0 ± 1500 84 ± 470 RV7-4812D15A1 36-75 10 363 ± 12 0 ± 625 87 ± 220 RV7-4815D15A1 36-75 10 359 ±15 0 ±500 88 ±100 NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg-electronic.de C1 L C2 RV7-12XXX15A1 1210,2.2uF/100V 12uH 1210,2.2uF/100V RV7-24XXX15A1 1210,2.2uF/100V 12uH 1210,2.2uF/100V RV7-48XXX15A1 1210,2.2uF/100V 12uH 1210,2.2uF/100V RV7 - XX XX S/D XX Power (W) Input Type A X Code internal Isolation (kVDC) |
Similar Part No. - RV7-1212S15A1 |
|
Similar Description - RV7-1212S15A1 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |