ADT7476AARQZ-R datasheet(10/69 Pages) ONSEMI

Part #	ADT7476AARQZ-R

Description	Remote Thermal Controller and Voltage Monitor

Download	69 Pages

Scroll/Zoom	100%

Manufacturer	ONSEMI [ON Semiconductor]

Direct Link	http://www.onsemi.com

Logo

10 / 69 page

ADT7476A

www.onsemi.com

10

clock pulse to assert a stop condition. In read

mode, the master device overrides the

acknowledge bit by pulling the data line high

during the low period before the ninth clock pulse.

This is known as no acknowledge. The master then

takes the data line low during the low period

before the 10th clock pulse, and then high during

the 10th clock pulse to assert a stop condition.

Any number of bytes of data can be transferred over the

serial bus in one operation. However, it is not possible to mix

read and write in one operation because the type of operation

is determined at the beginning and cannot subsequently be

changed without starting a new operation. In the

ADT7476A, write operations contain either one or two

bytes, and read operations contain one byte.

To write data to one of the device data registers or read

data from it, the address pointer register must be set so the

correct data register is addressed. Then, data can be written

into that register or read from it. The first byte of a write

operation always contains an address stored in the address

pointer register. If data is to be written to the device, then the

write operation contains a second data byte that is written to

the register selected by the address pointer register.

This write operation is illustrated in Figure 18. The device

address is sent over the bus, and then R/W is set to 0. This

is followed by two data bytes. The first data byte is the

address of the internal data register to be written to, which

is stored in the address pointer register. The second data byte

is the data to be written to the internal data register.

When reading data from a register, there are two

possibilities:

1. If the ADT7476A’s address pointer register value

is unknown, or not the desired value, then it must

first be set to the correct value before data can be

read from the desired data register. This is done by

performing a write to the ADT7476A as before,

but only the data byte containing the register

address is sent, because no data is written to the

register (see Figure 19).

A read operation is then performed consisting of

the serial bus address; R/W bit set to 1, followed

by the data byte read from the data register (see

Figure 20.)

2. If the address pointer register is already known to

be at the desired address, data can be read from the

corresponding data register without first writing to

the address pointer register (see Figure 20).

It is possible to read a data byte from a data register

without first writing to the address pointer register, if the

address pointer register is already at the correct value.

However, it is not possible to write data to a register without

writing to the address pointer register, because the first data

byte of a write is always written to the address pointer

register.

In addition to supporting the send byte and receive byte

protocols, the ADT7476A also supports the read byte

protocol. See Intel’s System Management Bus Specifications

Revision 2 for more information.

If several read or write operations must be performed in

succession, the master can send a repeat start condition

instead of a stop condition to begin a new operation.

Figure 18. Writing a Register Address to the Address Pointer Register, then Writing Data to the Selected Register

0

SCL

SDA

10

1

A1

A0

D7

D6

D5

D4

D3

D2

D1

D0

ACK. BY

ADT7476A

START BY

MASTER

19

1

ACK. BY

ADT7476A

9

D7

D6

D5

D4

D3

D2

D1

D0

ACK. BY

ADT7476A

STOP BY

MASTER

1

9

SCL (CONTINUED)

SDA (CONTINUED)

FRAME 1

SERIAL BUS ADDRESS BYTE

FRAME 2

ADDRESS POINTER REGISTER BYTE

FRAME 3

DATA BYTE

R/W

Figure 19. Writing to the Address Pointer Register Only

0

SCL

SDA

10

1

A1

A0

D7

D6

D5

D4

D3

D2

D1

D0

ACK. BY

ADT7476A

STOP BY

MASTER

START BY

MASTER

FRAME 1

SERIAL BUS ADDRESS BYTE

FRAME 2

ADDRESS POINTER REGISTER BYTE

1

9

ACK. BY

ADT7476A

9

R/W

Similar Part No. - ADT7476AARQZ-R

Manufacturer	Part #	Datasheet	Description
ON Semiconductor	ADT7476AARQZ-R	613Kb / 67P	dBCOOL Remote Thermal Controller and Voltage Monitor May, 2010 ??Rev. 3
Analog Devices	ADT7476AARQZ-REEL	1Mb / 72P	dBCool Remote Thermal Controller and Voltage Monitor REV. 0
Analog Devices	ADT7476AARQZ-REEL7	1Mb / 72P	dBCool Remote Thermal Controller and Voltage Monitor REV. 0
ON Semiconductor	ADT7476AARQZ-RL7	613Kb / 67P	dBCOOL Remote Thermal Controller and Voltage Monitor May, 2010 ??Rev. 3

More results

Similar Description - ADT7476AARQZ-R

Manufacturer	Part #	Datasheet	Description
ON Semiconductor	ADT7463	732Kb / 50P	Remote Thermal Controller and Voltage Monitor May, 2013 ??Rev. 7
ON Semiconductor	ADT7476	543Kb / 68P	Remote Thermal Controller and Voltage Monitor February, 2016 ??Rev. 10
Analog Devices	ADT7476	1Mb / 72P	dBCool Remote Thermal Controller and Voltage Monitor REV. A
Analog Devices	ADT7468	1,021Kb / 80P	dBCool??Remote Thermal Controller and Voltage Monitor REV. 0
ON Semiconductor	ADT7476A	613Kb / 67P	dBCOOL Remote Thermal Controller and Voltage Monitor May, 2010 ??Rev. 3
	ADM1027	1Mb / 56P	dBCOOL??Remote Thermal Controller and Voltage Monitor May 2010 - Rev. 3
	ADT7466	691Kb / 48P	dBCool짰 Remote Thermal Controller and Voltage Monitor May 2010 ??Rev. 3
	ADT7468	1Mb / 81P	dBCool짰 Remote Thermal Controller and Voltage Monitor May 2010 ??Rev. 3
	ADT7476	620Kb / 67P	dBCOOL Remote Thermal Controller and Voltage Monitor May, 2010 ??Rev. 6
Analog Devices	ADT7466	1Mb / 48P	dBCool Remote Thermal Controller and Voltage Monitor REV. 0

More results

ADT7476AARQZ-R Datasheet(PDF) 10 Page - ON Semiconductor

ADT7476AARQZ-R Datasheet(HTML) 10 Page - ON Semiconductor

Similar Part No. - ADT7476AARQZ-R

Similar Description - ADT7476AARQZ-R

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69

Datasheet Download

Link URL