Electronic Components Datasheet Search |
|
UCC28951QPWRQ1 Datasheet(PDF) 16 Page - Texas Instruments |
|
|
UCC28951QPWRQ1 Datasheet(HTML) 16 Page - Texas Instruments |
16 / 71 page SS SS(slave) T C 20.6 825k Ln 20.6 – 0.55 – EA+ = æ ö ´ ç ÷ è ø ( SS SS(master ) T 25 A C 0.55 ´ m = + ) EA+ 16 UCC28951-Q1 SLUSCK4 – OCTOBER 2016 www.ti.com Product Folder Links: UCC28951-Q1 Submit Documentation Feedback Copyright © 2016, Texas Instruments Incorporated Feature Description (continued) 7.3.4 Soft Start and Enable (SS/EN) The soft-start pin SS/EN is a multi-function pin used for the following operations: • Closed loop soft start with the gradual duty cycle increase from the minimum set by TMIN up to the steady state duty cycle required by the regulated output voltage. • Setting hiccup mode conditions during cycle-by-cycle overcurrent limit. • On/off control for the converter. During soft start, one of the voltages at the SS/EN or EA+ pins, whichever is lower (SS/EN – 0.55 V) or EA+ voltage (see Block Diagram), sets the reference voltage for a closed feedback loop. Both SS/EN and EA+ signals are non-inverting inputs of the error amplifier with the COMP pin being its output. Thus the soft start always goes under the closed feedback loop and the voltage at COMP pin sets the duty cycle. The duty cycle defined by the COMP pin voltage can not be shorter than TMIN pulse width set by the user. However, if the shortest duty cycle is set by the cycle-by-cycle current limit circuit, then it becomes dominant over the duty cycle defined by the COMP pin voltage or by the TMIN block. The soft-start duration is defined by an external capacitor CSS, connected between the SS/EN pin and ground, and the internal charge current that has a typical value of 25 µA. Pulling the soft-start pin externally below 0.55 V shuts down the controller. The release of the soft-start pin enables the controller to start, and if there is no current limit condition, the duty cycle applied to the output inductor gradually increases until it reaches the steady state duty cycle defined by the regulated output voltage of the converter. This happens when the voltage at the SS/EN pin reaches and then exceeds by 0.55 V, the voltage at the EA+ pin. Thus for the given soft-start time TSS, the CSS value can be defined by Equation 1 or Equation 2: (1) (2) For example, in Equation 1, if the soft-start time TSS is selected to be 10 ms, and the EA+ pin is 2.5 V, then the soft-start capacitor CSS is equal to 82 nF. NOTE If the converter is configured in Slave Mode and Hiccup Mode is not disabled, place a 825-kΩ ±5% resistor from SS pin to ground. 7.3.5 Light-Load Power Saving Features The UCC28951-Q1 offers four different light-load management techniques for improving the efficiency of a power converter over a wide load current range. 1. Adaptive Delay, (a) ADEL, which sets and optimizes the dead-time control for the primary switches over a wide load current range. (b) ADELEF, which sets and optimizes the delay-time control between the primary side switches and the secondary side switches. 2. TMIN, sets the minimum pulse width as long as the part is not in current limit mode. 3. Dynamic synchronous rectifier on/off control in DCM Mode, For increased efficiency at light loads. The DCM Mode starts when the voltage at CS pin is lower than the threshold set by the user. In DCM Mode, the synchronous output drive signals OUTE and OUTF are brought down low. 4. Burst Mode, for maximum efficiency at very light loads or no load. Burst Mode has an even number of PWM TMIN pulses followed by off time. Transition to the Burst Mode is defined by the TMIN duration set by the user. |
Similar Part No. - UCC28951QPWRQ1 |
|
Similar Description - UCC28951QPWRQ1 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |