ANALOG INPUTS*

Input Range: 4-20 mA, 0-10 VDC, RTD, thermocouple and 250 mV

Analog/Discrete Resolution: 16 bits (0.003%); 10 bits (1 ms fast option)

Input Impedance (Resistance): 100 ohms or 200 Kohms

Fuses: Self-resetting short circuit protection (4-20 mA inputs)

DMRR (Differential Mode): 66 db at 50/60 Hz

Update Time: 880 ms to 1 ms (configurable)

Temperature Accuracy: +/-0.5°C uncalibrated (typical)

RTD Type: 100 Ohm platinum

RTD Alpha: 0.00385 or 0.00392

RTD Connections: 2 or 3-wire

RTD Input Range: -200° to 850°C

ANALOG OUTPUTS*

Analog Output Range: 4-20 mA

Analog/Discrete Resolution: 16 bits (less than 1 uA)

Full Scale Accuracy: +/-0.02% (@20°C)

Span and Offset Temperature: +/- 50 ppm per °C

Load Resistance: 0-750 Ohms @ 24 VDC

Current Limiting Short Circuit Protection

RECOMMENDED WIRING CLEARANCE

Front: 2” (5.08 cm)

Top: 1” (2.54 cm)

ENVIRONMENTAL

Operating Temperature Range: -40° to +75°C

Storage Temperature: -40° to 85°C

Operating Humidity: 10% to 95% (Non Condensing)

Shock: IEC60068-2-6

Vibration: IEC60068-2-27

CERTIFICATION & COMPLIANCE

Hazardous Locations: ANSI/ISA 12.12.01-2013 Edition (Class I, Div. 2,

Groups A, B, C, and D), CSA C22.2/213;

Marine/Offshore: Rated per ABS, DNV and Lloyds

Electrical Safety: UL 508, CSA C22.2/142, EN/IEC61010-1, CE

EMI Emissions: FCC part 15, ICES-003, Class A,

EN-55022; EN6100-6-4, CE

EMC Immunity: EN61000-6-2, CE (EN61000-4-2,3,4,5,6,8); CE

Flammability: UL 94V-0 materials

MECHANICAL

Case Dimensions:

Height: 5.30” (134.6 mm)

Width: 5.60” (142.2 mm)

Depth: 2.85” (72.4 mm)

Weight: 2.5 lb.s (1.3 kg)

Mount: DIN Rail 35 mm

MTBF: >1M Hours**

WARRANTY

3 years on design and manufacturing defects

* See manual for model specific specifications

** Note: See Hardware Manual for model specific MTBF ratings.

E3 I/O Module Specifications

SWITCH PROPERTIES

Operation: Monitored

IEEE Compliance: 802.3, 802.3u, 802.3ab, 802.3x 802.1d/D/w,

802.1p, 802.1Q, 802.1x

Protocols: TCP/IP, ARP, UDP, ICMP, DHCP, HTTP, Modbus TCP,

Modbus UDP (slave or master), Sixnet TCP, Sixnet UDP

(slave or master)

Latency (typical): 5 us @ 100 Mbps

Switching Method: Store-and-Forward

Networks: 1 or 2 independent with unique MAC and IP addresses

Real-Time Ring: 30 ms + 5ms per hop

MDIX Auto Sensing Cable

Auto Sensing Speed and Flow Control

POWER INPUT*

Input Voltage: 10-30 VDC (12-24 Nominal)

Steady Input Current:

Maximum: 355mA @ 24VDC no loads

Average: 190mA @ 24VDC no loads

Minimum: 150mA @ 24VDC no loads

Max Inrush: 5 A /100 us @ 24 VDC

BTU/HR: 8 (typical)

CONNECTORS

Ethernet Ports: Two (2) 10/100Base-T(X) RJ45 ports

Serial Port: One (1) RS-485 screw block (485+, 485-, GND;

2-wire half-duplex, non-isolated)

RS-485 Networking: Up to 32 (full load) stations

RS-485 Distance: Up to 0.5 miles (baud-rate dependent)

Baud Rates: 300 to 57,600 baud

Protocols: Master and slave; Sixnet and Modbus RTU/ASCII

NETWORK MEDIA

10Base-T: ≥ Cat3 cable

100Base-T(X): ≥ Cat5 cable

DISCRETE INPUTS*

Voltage Range: 10-30 VDC or 60-140 VAC

Input Resolution: 150 volts (16 channel modules only)

Input Resistance: 10 Kohms

Slow Response: 25 ms (20 Hz max count rate)

Fast Response: 1 ms (400 Hz max count rate)

Special Fast Counting: Up to 50 KHz (channel 1 & 2)

Count Up: Pulse timing and pulse rate 16 or 32-bit reporting

DISCRETE OUTPUTS*

Output Voltage Range: 10-30 VDC or VDC/AC

Maximum Output Power: Up to .5 A per channel

Short Circuit Protection: Self-reset fuses

Input Isolation: 150 V (16 channel modules only)

Channel Scan Rate: 1 ms

DIMENSIONS in inches (mm)