Electronic Components Datasheet Search |
|
SN74ALVC3631-20PQ Datasheet(PDF) 7 Page - Texas Instruments |
|
SN74ALVC3631-20PQ Datasheet(HTML) 7 Page - Texas Instruments |
7 / 29 page SN74ALVC3631, SN74ALVC3641, SN74ALVC3651 512 × 36, 1024 × 36, 2048 × 36 SYNCHRONOUS FIRST-IN, FIRST-OUT MEMORIES SDMS025B – OCTOBER 1999 – REVISED JUNE 2000 7 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 serial load To program the X and Y registers serially, the device is reset with FS0/SD and FS1/SEN high during the low-to-high transition of RST. After this reset is complete, the X-and Y-register values are loaded bitwise through FS0/SD on each low-to-high transition of CLKA that FS1/SEN is low. Eighteen (SN74ALVC3631), twenty (SN74ALVC3641), and twenty-two (SN74ALVC3651) bit writes are needed to complete the programming. The first bit write stores the most-significant bit of the Y register and the last bit write stores the least-significant bit of the X register. Each register value can be programmed from 1 to 508 (SN74ALVC3631), 1 to 1020 (SN74ALVC3641), and 1 to 2044 (SN74ALVC3651). When the option is chosen to program the offset registers serially, the IR flag remains low until all register bits are written. The IR flag is set high by the low-to-high transition of CLKA after the last bit is loaded, to allow normal FIFO operation. FIFO write/read operation The state of the port-A data (A0–A35) outputs is controlled by the port-A chip select (CSA) and the port-A write/read select (W/RA). The A0–A35 outputs are in the high-impedance state when either CSA or W/RA is high. The A0–A35 outputs are active when both CSA and W/RA are low. Data is loaded into the FIFO from the A0–A35 inputs on a low-to-high transition of CLKA when CSA and the port-A mailbox select (MBA) are low, W/RA, the port-A enable (ENA), and the IR flag are high (see Table 2). Writes to the FIFO are independent of any concurrent FIFO reads. Table 2. Port-A Enable Function Table CSA W/RA ENA MBA CLKA A0–A35 OUTPUTS PORT FUNCTION H X X X X In high-impedance state None L H L X X In high-impedance state None L HH L ↑ In high-impedance state FIFO write L HH H ↑ In high-impedance state Mail1 write L L L L X Active, mail2 register None L LHL ↑ Active, mail2 register None L L L H X Active, mail2 register None L L H H ↑ Active, mail2 register Mail2 read (set MBF2 high) The port-B control signals are identical to those of port A, with the exception that the port-B write/read select (W/RB) is the inverse of the W/RA. The state of the port-B data (B0–B35) outputs is controlled by the port-B chip select (CSB) and W/RB. The B0–B35 outputs are in the high-impedance state when either CSB is high or W/RB is low. The B0–B35 outputs are active when CSB is low and W/RB is high. Data is read from the FIFO to its output register on a low-to-high transition of CLKB when CSB and MBB are low, W/RB, ENB, and the OR flag are high (see Table 3). Reads from the FIFO are independent of any concurrent FIFO writes. |
Similar Part No. - SN74ALVC3631-20PQ |
|
Similar Description - SN74ALVC3631-20PQ |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |