Electronic Components Datasheet Search |
|
AT88SC0104C-WI Datasheet(PDF) 3 Page - ATMEL Corporation |
|
AT88SC0104C-WI Datasheet(HTML) 3 Page - ATMEL Corporation |
3 / 17 page 3 AT88SC0104C 2021GS–SMEM–7/06 grammed into the 64-bit answer-to-reset register. An internal pull-up on the RST input pad allows the device to be used in synchronous mode without bonding RST. The AT88SC0104C does not support the synchronous answer-to-reset sequence. Serial Data (SDA/IO) The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wired with any number of other open drain or open collector devices. An exter- nal pull-up resistor should be connected between SDA and V CC. The value of this resistor and the system capacitance loading the SDA bus will determine the rise time of SDA. This rise time will determine the maximum frequency during read operations. Low value pull-up resistors will allow higher frequency operations while drawing higher aver- age power supply current. SDA/IO information applies to both asynchronous and synchronous protocols. When the synchronous protocol is used, the SCL/CLK input is used to positive edge clock data into the device and negative edge clock data out of the device. Table 2. DC Characteristics Applicable over recommended operating range from VCC = +2.7 to 5.5V, TAC = -40 oC to +85oC (unless otherwise noted) Symbol Parameter Test Condition Min Typ Max Units V CC Supply Voltage 2.7 5.5 V I CC Supply Current (V CC = 5.5V) Async READ at 3.57MHz 5 mA ICC Supply Current (VCC = 5.5V) Async WRITE at 3.57MHz 5 mA I CC Supply Current (V CC = 5.5V) Synch READ at 1MHz 5 mA ICC Supply Current (VCC = 5.5V) Synch WRITE at 1MHz 5 mA I SB Standby Current (V CC = 5.5V) V IN = VCC or GND 100 uA VIL SDA/IO Input Low Threshold(1) 0 VCC x 0.2 V V IL SCL/CLK Input Low Threshold(1) 0 V CC x 0.2 V VIL RST Input Low Threshold(1) 0 VCC x 0.2 V V IH SDA/IO Input High Threshold(1) V CC x 0.7 V CC V VIH SCL/CLK Input High Threshold(1) VCC x 0.7 VCC V V IH RST Input High Threshold(1) V CC x 0.7 V CC V IIL SDA/IO Input Low Current 0 < VIL < VCC x 0.15 15 uA I IL SCL/CLK Input Low Current 0 < V IL < VCC x 0.15 15 uA IIL RST Input Low Current 0 < VIL < VCC x 0.15 50 uA I IH SDA/IO Input High Current V CC x 0.7 < VIH < VCC 20 uA I IH SCL/CLK Input High Current V CC x 0.7 < VIH < VCC 100 uA IIH RST Input High Current VCC x 0.7 < VIH < VCC 150 uA V OH SDA/IO Output High Voltage 20K ohm external pull-up V CC x 0.7 V CC V VOL SDA/IO Output Low Voltage IOL = 1mA 0 VCC x 0.15 V IOH SDA/IO Output High Current VOH 20 uA Note: 1. V IIL min and VIH max are reference only and are not tested. |
Similar Part No. - AT88SC0104C-WI |
|
Similar Description - AT88SC0104C-WI |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |