150W Single Output Switching Power Supply

WWW.ASTRODYNETDI.COM

ASTRODYNE USA: 1-800-823-8082

ASTRODYNE PACIFIC: 886-2-26983458

INPUT SPECIFICATIONS

Input Voltage Range

88~132VAC / 176~240VAC selected

by switch 248~373 Volts(DC)

Frequency Range

47-63 Hz

Inrush Current, typ: (cold start)

40Amps / 230VAC

Input Current

3.0 Amps. @ 115VAC

2.0 Amps. @ 230VAC

Leakage current

< 2mAmps /240VAC

Min Load

See Selection Chart

OUTPUT SPECIFICATIONS

Voltage and Current

See Selection Chart

Line Regulation (Note 3)

±0.5%

Load Regulation (Note 4)

See Selection Chart

Voltage Tolerance (Note2)

See Selection Chart

Ripple/Noise (Note 1)

See Selection Chart

Hold Up Time @ FL

28mS/230VAC

20mS/115VAC

Setup, Rise Time @ FL

800ms, 20m/230VAC

1200mS, 30mS/115VAC

Over Voltage Protection

3.8 ~ 4.45Volt(DC): 3.3Volts(DC)

5.75 ~ 6.75Volt(DC): 5Volts(DC)

13.8 ~ 16.2Volt(DC): 12Volts(DC)

17.25 ~ 20.25Volt(DC): 15Volts(DC)

27.6~ 32.4Volt(DC): 24Volts(DC)

55.2~ 64.8Volt(DC): 48Volts(DC)

Hiccup mode, auto recover

Over Current Protection

110 ~ 150% rated output power

Hiccup mode, auto recover

DC Volt Adjust

See Selection Chart

GENERAL SPECIFICATIONS

Safety

UL60950-1,

TUV EN60950-1 Approved

Insulation Resistance

≥ 100MΩ / 500Volts(DC)

EMI

Compliance to EN55022 (CISPR22)

Class B

Harmonic Current

Compliance to EN61000-3-2,-3

Efficiency

74% (RS150-3.3)

78% (RS150-5)

83% (RS150-12)

84% (RS150-15)

86% (RS150-24)

87%(RS150-48)

Isolation

3000VAC Input - Output

1500VAC Input - Ground

500VAC Output - Ground

EMS

Compliance to

EN61000-4-2, 3, 4, 5, 6, 8, 11;

ENV50204,EN61000-6-2(EN50082-2)

heavy Industry Level, Criteria A

ENVIRONMENTAL SPECIFICATIONS

Oper. Temperature

-25°C to +70°C (See Derate Curve)

Storage Temperature

-40°C to +85°C, 10~95% RH

Relative Humidity

20~90% RH non cond

Temperature Coefficient

±0.03% / °C (0-50°C)

MTBF

244KHrs min,MIL-HDBK-217F(25°C)

Vibration

10~500Hz, 5G10min./1cycle, period for

60min. each along X, Y, Z axes

PHYSICAL SPECIFICATIONS

Size

Millimeters

199 x 98 x 38

Inches

7.83” x 3.86 ” x 1.50 ”

Weight

21.16 oz (600g)

NOTE

1. Ripple & noise are measured at 20MHz of bandwidth by using a 12”

twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

2. Tolerance : includes set up tolerance, line regulation and load regula-

tion.

3. Line regulation is measured from low line to high line at rated load.

4. Load regulation is measured from 0% to 100% rated load.

All specifications are typical at nominal input, full load, and 25°C unless other-

wise noted