Electronic Components Datasheet Search |
|
PN6013 Datasheet(PDF) 1 Page - Mallory performance club |
|
PN6013 Datasheet(HTML) 1 Page - Mallory performance club |
1 / 8 page Parts Included: 1 - Ignition Controller, PN 6013 1 - Pro-Data+ Software CD 1 - Parts Bag 1 - Mounting Template MSD 6-Hemi® Controller for Carbureted and EFI Hemi® Engines PN 6013 Parts Required, Not Supplied: A wiring harness is required to install the 6-Hemi Ignition Controller. For Carburetor Applications: '03-'05 Engines - PN 88863 '06-'07 Engines - PN 88864 On engines running factory EFI, one of the above harnesses is required along with a Tach Adapter Harness: '03-'05 - PN 88815 '05-'07 - PN 88816 WARNING: During installation, disconnect the battery cables. When Disconnecting, always remove the Negative cable first and install it last. Note: Solid core spark plug wires or non-resistor spark plugs cannot be used with an MSD Ignition Control. CARBURETOR OR EFI The PN 6013 Ignition Controller can be used for Hemi engines that have been retro-fit with an intake manifold and carburetor. A Coil Harness must be purchased separately. There are two different style coils used on late model Hemi engines; PN 88863 for '03-'05 models and PN 88864 for '06-'07 applications. For EFI applications, an additional harness will be required, harness PN 88815, for '03- '05 or PN 88816, for '06-'07 applications. This Adapter Kit allows the PN 6013 Controller to tap into the sensor signals without interrupting the OEM ECU. The ECU and coils operate as normal while the PN 6013 controls the timing and rpm. OPERATION The 6-Hemi Controller offers several programmable features. This can be achieved through the supplied Pro-Data+ software via a PC or with the optional Hand Held Programmer, PN 7550. Software installation, operation and the programmable features of the Controller are explained in detail in this document. More information can be found in the Pro-Data+ Software Help section. MOUNTING The 6-Hemi Controller is designed to be mounted under the hood or on the firewall. Do not mount the unit near exhaust. Find a suitable location, confirm that all of the wires reach their connections. Mark the mounting hole locations using the unit or the template supplied. Drill the holes with a 3/16" bit. WIRING All of the wiring, except four wires, are routed into factory style connectors to ensure an easy installation on a Hemi engine. Power wires: The power wires of the 6-Hemi are routed in a three wires sleeve, with Black connecting to ground and a Red/Green and Brown/Yellow going to a 2-pin connector. For carburetor installations, the Brown/Yellow will not be used and can be cut and sealed while the Red/Green wire is connected to switched 12 volts. The Red/Green wire can be removed from its sleeve close to the ground wires for easier routing to a 12 volt source. On EFI installations the 2-pin connector will plug into the OEM adapter (PN 88815, PN 88816). Optional Accessories: Hand Held Monitor, PN 7550 Hemi is a registered trademark of Chrysler LLC. MSD • W W W. M S D PE R F OR M A NC E . C OM • ( 91 5 ) 8 55 - 7 12 3 • F AX ( 91 5 ) 8 57 - 33 4 4 |
Similar Part No. - PN6013 |
|
Similar Description - PN6013 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |