Electronic Components Datasheet Search |
|
CMD15-21SRCTR8 Datasheet(PDF) 2 Page - Skyworks Solutions Inc. |
|
CMD15-21SRCTR8 Datasheet(HTML) 2 Page - Skyworks Solutions Inc. |
2 / 17 page AAT1274 1.5A Single Flash LED Driver IC DATA SHEET 2 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201981A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 21, 2012 Pin Descriptions Pin # Symbol Description 1,5 AGND Analog ground pin. Connect AGND to PGND, and FLGND at a single point as close to the AAT1274 as possible. 2 EN/SET Enable and Serial Control input. EN/SET is the AS2Cwire addressing and programming input to: a) adjust the movie-mode current level; b) select the Flash-to-Movie-mode ratio; 3 FL LED Flash current sink pin. Connect the cathode of Flash LED to FL. 4 FLEN Flash enable pin. A low-to-high transition on the FLEN pin initiates a flash pulse and a high-to-low transition on the FLEN pin terminates a flash pulse 6IN Flash output boost converter power input. Connect IN to the input power source. Connect a 2.2μF or larger ceramic capacitor from IN to PGND and locate as close as possible to the AAT1274 package for optimum per- formance. 7 PGND Power ground. Connect PGND to the same single point as AGND located as close to the AAT1274 as possible 8 OUT Power output of the boost converter. Connect a 2.2μF or larger ceramic capacitor from OUT to PGND as close as possible to the AAT1274. Connect OUT to the anode of the Flash LED. 9, 12 NC Not connected 10 SW Boost converter switching node. Connect a 1μH inductor between SW and IN. 11 FLINH Flash inhibit pin. FLINH is an active HIGH control input with an internal 200kΩ resistor to AGND. A low-to- high transition on the FLINH pin reduces FL sink current to the maximum (default) movie-mode current level. 13 FLGND Flash ground pin. Connect FLGND to PGND, and AGND at a single point as close to the AAT1274 as possible. 14 RSET Flash current set pin. Connect a resistor from RSET to AGND to program the desired flash current for the cur- rent sink FL. EP Electrical back contact. Connect to a good thermal ground pad Pin Configuration TDFN33-14 (Top View) AGND EN/SET FL 1 FLEN AGND IN RSET FLGND N/C FLINH SW N/C 2 3 4 5 6 PGND 7 12 11 14 13 10 9 OUT 8 |
Similar Part No. - CMD15-21SRCTR8 |
|
Similar Description - CMD15-21SRCTR8 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |