54

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

PLG

Radial Lead Type, Higher Capacitance

Specifications

Temperature Characteristics

(Max.Impedance Ratio)

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Tangent of loss angle (tan δ)

ESR (

1)

Leakage Current (

2)

Performance Characteristics

Item

– 55 to +105°C

2.5 to 16V

330 to 3900µF

± 20% at 120Hz, 20°C

Less than or equal to the specified value at 120Hz, 20°C

Less than or equal to the specified value at 100kHz, 20°C

Less than or equal to the specified value.

After 2 minutes' application of rated voltage at 20°C

Z+105°C / Z+20°C

1.25

(100kHz)

Z

– 55°C / Z+20°C

1.25

Endurance

Damp Heat

(Steady State)

Resistance to

Soldering Heat

Marking

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 2000 hours at 105°C.

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 1000 hours at 60°C, 90% RH.

After soldering the capacitor under the soldering conditions prescribed

here as preheat at 150 to 200°C for 60 to 180 seconds and peak

temperature at 265°C for 10 seconds or less, the capacitor shall meet

the specifications listed at right, provided that its temperature profile is

measured at both of terminal ends facing the soldering side.

Navy blue print on the case top

Capacitance change

tan δ

Leakage current (

2)

1)

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

150% or less than the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current (

2)

1)

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

150% or less than the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current (

2)

1)

Within ± 10% of the initial capacitance value ( 3)

130% or less than the initial specified value

130% or less than the initial specified value

Less than or equal to the initial specified value

Higher Capacitance, Low ESR, High ripple current.

Load life of 2000 hours at 105°C.

Radial lead type :

Lead free flow soldering condition correspondence

Compliant to the RoHS directive (2011/65/EU).

1 ESR should be measured at both of the terminal ends closest to the capacitor body.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

P

1

L

2

G

3

0

4

G

5

1

6

2

7

2

8

M

9

C

10

O

11

1

12

Configuration

Size code

Capacitance tolerance (±20%)

Rated capacitance (1200µF)

Rated voltage (4V)

Series name

Type

L+0.5MAX.

15MIN

4MIN

Resin coated Case

φd

Capacitance

Series

Lot. No.

Voltage(g:4V)

Dimensions

Type numbering system (Example : 4V 1200µF)

Size

φD

L

P

φd

φ8

8.0

8.5

3.5

0.6

φ8

8.0

11.5

3.5

0.6

φ10

10.0

12.5

5.0

0.6

(mm)

Dimension table in next page.

PLG

PLF

Higher

Capacitance

Voltage

V

2.5

4

6.3

10

16

Code

e

g

j

A

C

Please refer to page 20 about the end seal configuration.

CAT.8100E