Electronic Components Datasheet Search |
|
ELM613DA Datasheet(PDF) 7 Page - ELM Electronics |
|
ELM613DA Datasheet(HTML) 7 Page - ELM Electronics |
7 / 11 page 7 Rev.1.3 11 - In this case, a third pole set by the compensation capacitor (C4) and the compensation resistor (R3) is used to compensate the effect of the ESR zero on the loop gain. This pole is located at: fp3 = 1 / (2π × C4 × R3) The goal of compensation design is to shape the converter transfer function to get a desired loop gain. The sys- tem crossover frequency where the feedback loop has the unity gain is important. Lower crossover frequencies result in slower line and load transient responses, while higher crossover frequencies could cause system insta- bility. A good rule of thumb is to set the crossover frequency below one-tenth of the switching frequency. To optimize the compensation components, the following procedure can be used. 1) Choose the compensation resistor (R3) to set the desired crossover frequency. Determine the R3 value by the following equation: R3 = [ (2π × Cout × fc) / (Gea × Gcs) ] × (Vout/Vfb) < [ (2π × Cout × 0.1 × fs) / (Gea × Gcs) ] × (Vout/Vfb) Where fC is the desired crossover frequency which is typically below one tenth of the switching frequency. 2) Choose the compensation capacitor (C1) to achieve the desired phase margin. For applications with typical inductor values, setting the compensation zero, fz1, below one-forth of the crossover frequency provides suffi- cient phase margin. Determine the C1 value by the following equation: C1 > 4 / (2π × R3 × fc) Where R3 is the compensation resistor. 3) Determine if the second compensation capacitor (C4) is required. It is required if the ESR zero of the output capacitor is located at less than half of the switching frequency, or the following relationship is valid: 1 / (2π × Cout × Resr) < fs/2 If this is the case, then add the second compensation capacitor (C4) to set the pole fP3 at the location of the ESR zero. Determine the C4 value by the equation: C4 = (Cout × Resr) / R3 8. External bootstrap diode An external bootstrap diode may enhance the efficiency of the regulator, the applicable conditions of external BS diode are: Vout = 5V or 3.3V, and duty cycle is high: D = Vout/Vin > 65% In these cases, an external BS diode is recommended from the output of the voltage regulator to BS pin, as shown in Figure 1. SW Cout BS Cbs 0.1 to 1µF L ELM613DA External BS diode IN4148 5V or 3.3V ◄ Figure 1. Add optional external bootstrap diode to enhance efficiency. ELM613DA 2A, 20V, 550kHz, synchronous step-down DC/DC converter The recommended external BS diode is IN4148, and the BS capacitor is 0.1 to 1μF. |
Similar Part No. - ELM613DA |
|
Similar Description - ELM613DA |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |