D/CRCW-P

www.vishay.com

Vishay

Revision: 21-Jan-14

5

Document Number: 20009

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

All tests are carried out in accordance with the following specifications:

• EN 60115-1, generic specification

• EN 140400, sectional specification

• EN 140401-802, detail specification

• IEC 60068-2-x, variety of environmental test procedures

Packaging of components is done in paper or blister tapes according to IEC 60286-3.

4.23

-

Climatic sequence:

-

± (1 % R + 0.05

)

4.23.2

2 (Ba)

Dry heat

125 °C; 16 h

4.23.3

30 (Db)

Damp heat, cyclic

55 °C;

 90 % RH;

24 h; 1 cycle

4.23.4

1 (Aa)

Cold

- 55 °C; 2 h

4.23.5

13 (M)

Low air pressure

1 kPa; (25 ± 10) °C; 1 h

4.23.6

30 (Db)

Damp heat, cyclic

55 °C;

 90 % RH;

24 h; 5 cycles

4.23.7

-

DC load

U =

4.25.1

-

Endurance at 70 °C

U =

 U

max.;

1.5 h on; 0.5 h off;

70 °C; 1000 h

± (1 % R + 0.05

)

70 °C; 8000 h

± (2 % R + 0.05

)

4.18.2

58 (Td)

Resistance to

soldering heat

Solder bath method

(260 ± 5) °C;

(10 ± 1) s

± (0.25 % R + 0.05

)

4.35

-

Flamability,

needle flame test

IEC 60695-11-5;

10 s

No burning after 30 s

4.24

78 (Cab)

Damp heat,

steady state

(40 ± 2) °C;

(93 ± 3) % RH;

56 days

± (1 % R + 0.05

)

4.25.3

-

Endurance at

upper category

temperature

155 °C, 1000 h

± (1 % R + 0.05

)

4.40

-

Electrostatic

discharge

(human body model)

IEC 61340-3-1;

3 pos. + 3 neg. discharges;

ESD voltage acc. to size

± (1 % R + 0.05

)

4.29

45 (XA)

Component solvent

resistance

Isopropyl alcohol;

50 °C; method 2

No visible damage

4.30

45 (XA)

Solvent resistance

of marking

Isopropyl alcohol;

50 °C; method 1,

toothbrush

Marking legible,

no visible damage

4.22

6 (Fc)

Vibration, endurance

by sweeping

f = 10 Hz to 2000 Hz;

x, y, z

 1.5 mm;

A

10 sweeps per axis

± (0.25 % R + 0.05

)

4.37

-

Periodic electric

overload

U =

 2 x U

max.;

0.1 s on; 2.5 s off;

1000 cycles

± (1 % R + 0.05

)

4.27

-

Single pulse high

voltage overload,

10 μs/700 μs

Û = 10 x

 2 x U

max.;

10 pulses

± (1 % R + 0.05

)

TEST PROCEDURES AND REQUIREMENTS

EN 60115-1



CLAUSE

IEC

60068-2

TEST

METHOD

TEST

PROCEDURE

REQUIREMENTS

PERMISSIBLE CHANGE (

R)

Stability for product types:

STABILITY CLASS 1 OR BETTER

D/CRCW-P

1

 to 10 M

P

P

15 x P

P