 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
IR3865M Datasheet(PDF) 11 Page - International Rectifier |
|
||||||||||||||||||||||||||||||
IR3865M Datasheet(HTML) 11 Page - International Rectifier |
|
|
11 / 22 page  IR3865MPBF 11 8/8/2012 Rev3.1 PWM COMPARATOR The PWM comparator initiates a SET signal (PWM pulse) when the FB pin falls below the reference (VREF) or the soft start (SS) voltage. ON-TIME GENERATOR The PWM on-time duration is programmed with an external resistor (R FF) from the input supply (VIN) to the FF pin. The simplified equation for R FF is shown in equation 1. The FF pin is held to an internal reference after EN goes HIGH. A copy of the current in R FF charges a timing capacitor, which sets the on-time duration, as shown in equation 2. CONTROL LOGIC The control logic monitors input power sources, sequences the converter through the soft-start and protective modes, and initiates an internal RUN signal when all conditions are met. VCC and 3VCBP pins are continuously monitored, and the IR3865 will be disabled if the voltage of either pin drops below the falling thresholds. EN_DELAY will become HIGH when VCC and 3VCBP are in the normal operating range and the EN pin = HIGH. SOFT START With EN = HIGH, an internal 10µA current source charges the external capacitor (C SS) on the SS pin to set the output voltage slew rate during the soft start interval. The soft start time (t SS) can be calculated from equation 3. The feedback voltage tracks the SS pin until SS reaches the 0.5V reference voltage (Vref), then feedback is regulated to Vref. C SS will continue to be charged, and when SS pin reaches VSS (see Electrical Specification), SS_DELAY goes HIGH. With EN_DELAY = LOW, the capacitor voltage and SS pin is held to the FB pin voltage. A normal startup sequence is shown in Figure 20. CIRCUIT DESCRIPTION (2) V 20 1 R T IN FF ON pF V (1) F 20 1 V R SW OUT FF pF V (3) A 10 5 . 0 V C t SS SS Figure 20. Normal Startup PGOOD The PGOOD pin is open drain and it needs to be externally pulled high. High state indicates that output is in regulation. The PGOOD logic monitors EN_DELAY, SS_DELAY, and under/over voltage fault signals. PGOOD is released only when EN_DELAY and SS_DELAY = HIGH and output voltage is within the OV and UV thresholds. PRE-BIAS STARTUP IR3865 is able to start up into pre-charged output, which prevents oscillation and disturbances of the output voltage. With constant on-time control, the output voltage is compared with the soft start voltage (SS) or Vref, depending on which one is lower, and will not start switching unless the output voltage drops below the reference. This scheme prevents discharge of a pre-biased output voltage. SHUTDOWN The IR3865 will shutdown if VCC is below its UVLO limit. The IR3865 can be shutdown by pulling the EN pin below its lower threshold. Alternatively, the output can be shutdown by pulling the soft start pin below 0.3V. |
Similar Part No. - IR3865M |
|
Similar Description - IR3865M |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
