Electronic Components Datasheet Search
  English  ▼

Delete All
ON OFF
ALLDATASHEET.COM

X  

Preview PDF Download HTML

LS7232NT Datasheet(PDF) 1 Page - LSI Computer Systems

Part No. LS7232NT
Description  PROXIMITY/TOUCH CONTROL HALOGEN LAMP DIMMER
Download  7 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Maker  LSI [LSI Computer Systems]
Homepage  http://www.lsicsi.com
Logo 

LS7232NT Datasheet(HTML) 1 Page - LSI Computer Systems

   
Zoom Inzoom in Zoom Outzoom out
 1 / 7 page
background image
PROXIMITY/TOUCH CONTROL HALOGEN LAMP DIMMER
DESCRIPTION:
LS7232NT is a CMOS integrated circuit designed for brightness
control of incandescent lamps or tranformer coupled low voltage
halogen lamps. The brightness is controlled by controlling the fir-
ing angle of a triac in series with the lamp and triggered by the
LS7232NT. A Phase-Locked-Loop keeps the LS7232NT phase
pointer locked in phase with the line voltage.
A unique optical user interface provides for a smooth control of
the lamp intensity without the need for touching any sensor
plate. A mechanical switch interface for dimming control is also
provided which can be used for a remote touch plate. The IC in-
cludes features to address problems associated with inductive
loads such as transformers in low voltage halogen lamp applica-
tion. The voltage to current phase lag resulting from the in-
ductance may prevent the triac from shutting off at AC zero
crossover and/or prevent the triac from maintaining conduction
following the removal of the gate trigger.
These problems are addressed by the LS7232NT in the fol-
lowing manner:
1. Compensation for delayed triac cut-off.
When trigger pulse is due to occur at a conduction angle
which coincides with the on-state of the triac, the trigger
pulse is delayed until the triac has turned off. This elim-
inates the underlying cause of half-waving.
2. Compensation for delayed triac turn-on.
At the set conduction angle, a triac trigger pulse of 130.2µs
(60Hz) is issued by the dimmer IC. If the triac fails to fire, a
second trigger pulse of 260.4µs width is issued a milli-
second later as a second attempt to fire the triac during the
same half-cycle.
3. Safety-Shutdown.
If the frequency of occurrences of the delayed cut-off and
the delayed turn-on exceeds a preset threshold, a shut-
down is initiated by turning off the triac trigger pulses. The
safety-shutdown threshold value is accumulated in a 4-bit
Up/Down counter. The count increments for every oc-
currence of delayed cut-off or delayed turn-on and decre-
ments once every 8 SYNC pulses (AC line cycles). The
count will not decrement below zero. If the count reaches
15, the safety-shut-down is effected.
PIN ASSIGNMENT - TOP VIEW
1
2
3
4
5
6
7
8
9
10
11
12
13
14
LS7232NT
CAP
SYNC
ANODE
CATHODE
PHOTOUT
SENS
REMOTE
V DD (+V)
M2
M1
RC
LEDO
TRIG/
Vss (-V)
FIGURE 1
The LS7232NT can be configured in 7 different modes of dim-
ming and timing off functions selected by two 3-state mode
pins.
INPUT/OUTPUT DESCRIPTION:
CAP (Pin 1)
PLL filter capacitor input. A 0.02µF capacitor is required at this
input for the optimal operation of the PLL.
SYNC (Pin 2)
The phase pointer for the triac trigger signal is synchronized
with the 50Hz/60Hz AC voltage applied at the SYNC input by
the internal PLL. The triac On/Off status information is also de-
rived from this input.
ANODE (Pin 3) CATHODE (Pin 4) and PHOTOUT (Pin 5)
These three pins constitute the input/outputs of a trans-
conductance and voltage amplifier pair (See Fig. 6) for con-
verting the current from a photo-diode to a voltage stimulus for
application at the SENS input. The photo-signal is used in lieu
of a touch plate for a touchless dimmer system. The output at
PHOTOUT is governed by the following equation:
VOUT = VDD/2 + 2IDRf
Where VDD = Supply Voltage
ID = Current in Photo-diode connected between
ANODE and CATHODE
Rf = Feedback resistance between PHOTOUT
and CATHODE
A potentiometer is used for Rf for controlling the sensitivity of
the photo-amplifier system.
7232NT-111501-1
November 2001
FEATURES:
Control of incandescent and transformer coupled
halogen lamps.
No-Touch lamp control through optical sensing
PLL synchronization of AC for wall switch application.
Extension input for remote control
Safety-shutdown for transformer malfunction.
Pin-selectable operating modes
Single 5V power supply
50Hz/60Hz AC line frequency
LS7232NT (DIP), LS7232NT-S (SOIC) - See Figure 1
LSI/CSI
LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747
(631) 271-0400 FAX (631) 271-0405
LS7232NT
UL
®
A3800


Html Pages

1  2  3  4  5  6  7 


Datasheet Download



Related Electronics Part Number

Part NumberComponents DescriptionHtml ViewManufacturer
LS7631TOUCH CONTROL HALOGEN LAMP DIMMER 1 2 3 4 LSI Computer Systems
LS7231TOUCH CONTROL LAMP DIMMER 1 2 3 4 5 MoreLSI Computer Systems
LS7237TOUCH CONTROL LAMP STEP DIMMER 1 2 3 4 LSI Computer Systems
LS7232NDTOUCH CONTROL LAMP DIMMER 1 2 3 4 5 LSI Computer Systems
CM2059T-2 3/4 Miniature Bayonet Base Halogen Lamp 1 Chicago Miniature Lamp,inc
CM1974T-3 Special Service Halogen Lamp 1 Chicago Miniature Lamp,inc
LS7538TOUCH CONTROL STEP DIMMER LIGHT SWITCH WITH AUTOMATIC GAIN CONTROL AGC 1 2 3 4 LSI Computer Systems
CM1964Axial Filament Halogen Lamp 1 Chicago Miniature Lamp,inc
L9830MONOLITHIC LAMP DIMMER 1 2 3 4 5 MoreSTMicroelectronics
CM449X12VMarine Halogen Lamp 1 Chicago Miniature Lamp,inc

Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ]  

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Alldatasheet API   |   Link Exchange   |   Manufacturer List
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn