Electronic Components Datasheet Search |
|
LTC1420CGN Datasheet(PDF) 4 Page - Linear Technology |
|
LTC1420CGN Datasheet(HTML) 4 Page - Linear Technology |
4 / 20 page 4 LTC1420 SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VDD Positive Supply Voltage (Note 10) 4.75 5.25 V OVDD Output Supply Voltage (Note 10) 2.7 5.25 V VSS Negative Supply Voltage Dual Supply Mode – 5.25 – 4.75 V Single Supply Mode 0 V IDD Positive Supply Current q 48 58 mA ISS Negative Supply Current q 1.4 2.5 mA PD Power Dissipation q 250 300 mW SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS fSAMPLE Maximum Sampling Frequency q 0.02 10 MHz tCONV Conversion Time q 70 90 ns tACQ Acquisition Time q 10 30 ns tH CLK High Time q 20 50 ns tL CLK Low Time q 20 50 ns tAP Aperature Delay of Sample-and-Hold – 250 ps Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: All voltage values are with respect to ground with GND and OGND wired together (unless otherwise noted). Note 3: When these pin voltages are taken below VSS or above VDD, they will be clamped by internal diodes. This product can handle input currents greater than 100mA below VSS or above VDD without latchup. Note 4: When these pin voltages are taken below VSS they will be clamped by internal diodes. This product can handle input currents greater than 100mA below VSS without latchup. GAIN is not clamped to VDD. When CLK is taken above VDD, it will be clamped by an internal diode. The CLK pin can handle input currents of greater than 100mA above VDD without latchup. Note 5: VDD = 5V, VSS = – 5V or 0V, fSAMPLE = 10MHz, tr = tf = 5ns unless otherwise specified. Note 6: Dynamic specifications are guaranteed for dual supply operation with a single-ended + AIN input and – AIN grounded. For single supply dynamic specifications, refer to the Typical Performance Characteristics. Note 7: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band. Note 8: Bipolar offset is the offset voltage measured from –0.5LSB when the output code flickers between 0000 0000 0000 and 1111 1111 1111. Note 9: Guaranteed by design, not subject to test. Note 10: Recommended operating conditions. The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. Specifications are guaranteed for both dual supply and single supply operation. (Note 5) The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. Specifications are guaranteed for both dual supply and single supply operation. (Note 5) POWER REQUIRE E TS TI I G CHARACTERISTICS |
Similar Part No. - LTC1420CGN |
|
Similar Description - LTC1420CGN |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |