![]() |
Electronic Components Datasheet Search |
|
HIP4081 Datasheet(PDF) 4 Page - Intersil Corporation |
|
HIP4081 Datasheet(HTML) 4 Page - Intersil Corporation |
4 / 18 page ![]() 4 Absolute Maximum Ratings Thermal Information (Typical, Note 1) Supply Voltage, VDD and VCC . . . . . . . . . . . . . . . . . . . -0.3V to 16V Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V Voltage on AHS, BHS . . . . -6.0V (Transient) to 80V (25oC to 125oC) Voltage on AHS, BHS . . . -6.0V (Transient) to 70V (-55oC to 125oC) Voltage on ALS, BLS . . . . . . . -2.0V (Transient) to +2.0V (Transient) Voltage on AHB, BHB . . . . . . . VAHS, BHS -0.3V to VAHS, BHS +16V Voltage on ALO, BLO . . . . . . . . . . . . VALS, BLS -0.3V to VCC +0.3V Voltage on AHO, BHO . . . . . . VAHS, BHS -0.3V to VAHB, BHB +0.3V Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . . . -5mA to 0mA Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns NOTE: All voltages are relative to pin 4, VSS, unless otherwise specified. Storage Temperature Range . . . . . . . . . . . . . . . . . . .-65oC to 150oC Operating Max. Junction Temperature . . . . . . . . . . . . . . . . . . 125oC Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . . 300oC (For SOIC - Lead Tips Only) Thermal Resistance, Junction-Ambient SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85oC/W DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75oC/W CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. θJA is measured with the component mounted on an evaluation PC board in free air. Operating Conditions Supply Voltage, VDD and VCC . . . . . . . . . . . . . . . . . . . +6V to +15V Voltage on ALS, BLS . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +1.0V Voltage on AHB, BHB . . . . . . . . VAHS, BHS +5V to VAHS, BHS +15V Input Current, HDEL and LDEL. . . . . . . . . . . . . . . . -500 µA to -50µA Operating Ambient Temperature Range . . . . . . . . . . .-40oC to 85oC Electrical Specifications VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL = 100K and TA = 25 oC, Unless Otherwise Specified PARAMETER SYMBOL TEST CONDITIONS TJ = 25 oC TJS = -40 oC TO 125oC UNITS MIN TYP MAX MIN MAX SUPPLY CURRENTS AND CHARGE PUMPS VDD Quiescent Current IDD All Inputs = 0V 7 9 11 6 12 mA VDD Operating Current IDDO Outputs Switching f = 500kHz 8 9.5 12 7 13 mA VCC Quiescent Current ICC All Inputs = 0V, IALO = IBLO = 0 - 0.1 10 - 20 µA VCC Operating Current ICCO f = 500kHz, No Load 1 1.25 2.0 0.8 3 mA AHB, BHB Quiescent Current - Qpump Output Current IAHB, IBHB All Inputs = 0V, IAHO = IBHO = 0 VDD = VCC = VAHB = VBHB = 10V -50 -30 -15 -60 -10 µA AHB, BHB Operating Current IAHBO, IBHBO f = 500kHz, No Load 0.5 0.9 1.3 0.4 1.7 mA AHS, BHS, AHB, BHB Leakage Current IHLK VAHS = VBHS = VAHB = VBHB = 95V - 0.02 1.0 - 10 µA AHB-AHS, BHB-BHS Qpump Output Voltage VAHB-VAHS VBHB-VBHS IAHB = IAHB = 0, No Load 11.5 12.6 14.0 10.5 14.5 V INPUT PINS: ALI, BLI, AHI, BHI, AND DIS Low Level Input Voltage VIL Full Operating Conditions - - 1.0 - 0.8 V High Level Input Voltage VIH Full Operating Conditions 2.5 - - 2.7 - V Input Voltage Hysteresis - 35 --- mV Low Level Input Current IIL VIN = 0V, Full Operating Conditions -130 -100 -75 -135 -65 µA High Level Input Current IIH VIN = 5V, Full Operating Conditions -1 - +1 -10 +10 µA TURN-ON DELAY PINS: LDEL AND HDEL LDEL, HDEL Voltage VHDEL, VLDEL IHDEL = ILDEL = -100µA 4.9 5.1 5.3 4.8 5.4 V GATE DRIVER OUTPUT PINS: ALO, BLO, AHO, AND BHO Low Level Output Voltage VOL IOUT = 100mA 0.7 0.85 1.0 0.5 1.1 V High Level Output Voltage VCC -VOH IOUT = -100mA 0.8 .95 1.1 0.5 1.2 V HIP4081 |