Electronic Components Datasheet Search
  English  ▼

Delete All
ON OFF
ALLDATASHEET.COM

X  

Preview PDF Download HTML

HIP0063 Datasheet(PDF) 1 Page - Intersil Corporation

Part No. HIP0063
Description  Hex Low Side MOSFET Driver with Serial or Parallel Interface and Diagnostic Fault Control
Download  8 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Maker  INTERSIL [Intersil Corporation]
Homepage  http://www.intersil.com/cda/home
Logo 

HIP0063 Datasheet(HTML) 1 Page - Intersil Corporation

   
Zoom Inzoom in Zoom Outzoom out
 1 / 8 page
background image
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207
| Copyright
© Intersil Corporation 1999
HIP0063
Hex Low Side MOSFET Driver with Serial or
Parallel Interface and Diagnostic Fault Control
Description
The HIP0063 is a logic controlled, six channel Low Side Power Driver. As
shown in the Block Diagram, the outputs are controlled via the serial data
interface or, by user option, each output may be independently controlled
from the respective parallel input. In addition, PWM logic switching control
(HLOS) may be directly applied to channels 0 and 1 in parallel, or channels 4
and 5 in parallel.
Output fault conditions may be detected as an output load short to supply
when the output is ON or as an open load/ground short when the output is
OFF. If an over-current short exists at one output, gate drive goes to a low
duty cycle mode. It will remain in the low duty cycle mode until switched off or
the fault is cleared. Fault bits are sent to a fault register to indicate which
channel is at fault. The fault bits are indicated by a logic one and is internally
latched when CS goes low. A fault bit will return to zero when the fault disap-
pears. Either an 8-bit or 16-bit SPI communication mode may be used. Refer
to the application section for bit control information.
Over-voltage shutdown protection for all outputs will occur when VPWR (Battery/
MOSFET Supply) exceeds 35V typical. When VCC is less than 3.5V, gate drive
is switched off. The input and gate control logic is fully function when the VCC
supply is greater than 4V typical. The HIP0063 has an internal drain-to-gate
zener which is used to voltage clamp the output drain-to-source voltage of the
MOSFET.
The HIP0063 is fabricated in a Power BiMOS IC process, and is intended for
use in automotive and other applications having a wide range of temperature
and electrical stress conditions. It is particularly well suited for MOSFET con-
trol in circuits driving lamps, displays, relays, and solenoids in applications
requiring low operating power.
Ordering Information
PART
NUMBER
TEMPERATURE
RANGE
PACKAGE
HIP0063AB
-40oC to +125oC
28 Lead Plastic SOIC (W)
Features
• Six Channel MOSFET Driver with Gate Drive
Control by Serial (SPI) or Parallel Interface and
an Option for PWM Logic Switching Control
• Drain Monitor Provides Fault Detection and
Voltage Clamp for Each Channel
• Output Voltage Zener Clamp. . . . . . . . . . 67V Typ
• 5V CMOS Logic Level Input Control
•VCC Logic Level Power Supply
- 5V VCC Logic Power Supply
- Turns Off Gate Drive for Low or Loss of VCC
•VPWR System Level Power Supply Management
- 5.5V to 17V Battery/System Level Power
Supply Monitor
- Over-Voltage Shutdown . . . . . . . . . . . . 35V Typ
• Output Supply/Load Short and Open
Load/Ground Short Fault Detection
• Automatic Change to Low Duty Cycle Drive
Mode When Output Short-to-Supply Detected
• Fault Diagnostic Feedback via the SPI Bus
• Operating Temp Range . . . . . . . -40oC to +125oC
Applications
• Automotive and Industrial Systems
• Control of Solenoids, Relays and Lamp Drivers
• Interface to Logic and
µP Controllers
• Robotic System Controller
PRELIMINARY
October 1995
Pinout
HIP0063 SOIC
TOP VIEW
Block Diagram
HLOS
HPW01
HPW45
P10
P11
P12
P13
P14
P15
CS
SO
SI
SCK
GND
VPWR
D0
G1
D1
D2
G3
D4
G4
D5
G5
VCC
G0
G2
D3
28
27
26
25
24
23
22
21
20
19
18
17
16
15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
D0
FAULT LOGIC
PI0-5
MUX
POR
HLOS
VCC
HPW45
HPW01
S6
OSC AND
VPWR
OVSD
GATE
CONTROL
P0
LOGIC
F0
G0
AND LATCH
OVSD
TIME DELAY
CONTROL
FAULT DATA
GND
S0
CHANNEL#0 - (1 OF 6)
TG
TG
+5V
(DRAIN
(GATE DR.
SPI (SER.)
CONTROL
PWM
CONTROL
(6)
SCK
CS
SI
SO
F0-5
S0-5
POR
+VPWR
HIP0063
EXT POWER
MOSFET AND
TYP LOAD
VOLT.,VG)
MONITOR
VOLT,VDM)
PI0-5
File Number
4009


Html Pages

1  2  3  4  5  6  7  8 


Datasheet Download




Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ]  

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Alldatasheet API   |   Link Exchange   |   Manufacturer List
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn