Electronic Components Datasheet Search
  English  ▼

Delete All
ON OFF
ALLDATASHEET.COM

X  

Preview PDF Download HTML

HT-0102 Datasheet(PDF) 7 Page - FCI connector

Part No. HT-0102
Description  HT-0102 Hand Tool Manual
Download  10 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Maker  FCI-CONNECTOR [FCI connector]
Homepage  http://www.fciconnect.com
Logo FCI-CONNECTOR - FCI connector

HT-0102 Datasheet(HTML) 7 Page - FCI connector

Back Button HT-0102 Datasheet HTML 2Page - FCI connector HT-0102 Datasheet HTML 3Page - FCI connector HT-0102 Datasheet HTML 4Page - FCI connector HT-0102 Datasheet HTML 5Page - FCI connector HT-0102 Datasheet HTML 6Page - FCI connector HT-0102 Datasheet HTML 7Page - FCI connector HT-0102 Datasheet HTML 8Page - FCI connector HT-0102 Datasheet HTML 9Page - FCI connector HT-0102 Datasheet HTML 10Page - FCI connector  
Zoom Inzoom in Zoom Outzoom out
 7 / 10 page
background image
ELECTRONICS
FCI Electronics
Manual Part No. 144000-001
Issued: Date (10/24/94)
Page 7 of 10
Rev. 03/08/01 ECR V103118
Revision B
K\DCU\Manuals
IV. PARTS REPLACEMENT
PROCEDURES
A. Anvil Replacement
Replace anvils when they show excessive wear or become
cracked or chipped.
Removal
1
Remove the cap screw securing the anvil holder assembly
to the hand tool (see Figure 6) and then remove the anvil
holder assembly.
Figure 6
2
Loosen the two setscrews in the anvil holder and remove
the terminal holder (see Figure 7).
Figure 7
3
Remove the cap screw and defective anvil(s) from the
anvil holder (see Figure 8).
Figure 8
Installation
NOTE
When replacing the anvils, be sure that the part number for
the new anvil(s) is the same as the one being replaced.
1
Loosely install the new anvils to the anvil holder
with the attaching cap screw (See Figure 8).
2
Reinstall the anvil holder onto the hand tool and
tighten the attaching cap screw.
3
Cut out two strips of paper. Then fold the strips in
half and place them over the anvils (see Figure 9).
Figure 9
4
Slowly close the hand tool lever completely. This will
align the anvils to the crimpers. Then tighten the anvil
cap screw and release the lever. Next, remove the
paper from the anvils.
5
Reinstall the terminal holder to the anvil holder. Make
sure that the flats on the end of the terminal holder
guide pins face the setscrews in the anvil holder. Then
tighten the anvil holder set screws.
6
Crimp a terminal to the proper size wire. Then inspect
the terminal as described in section II, paragraph B.
CAUTION
To prevent the anvils from being
damaged during alignment, place a
piece of paper over the anvils.
PDM: Rev:B
Released
STATUS:
Printed: Dec 20, 2002


Html Pages

1  2  3  4  5  6  7  8  9  10 


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ]  

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Alldatasheet API   |   Link Exchange   |   Manufacturer List
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn