Electronic Components Datasheet Search
  English  ▼

Delete All
ON OFF
ALLDATASHEET.COM

X  

Preview PDF Download HTML

HT-0102 Datasheet(PDF) 6 Page - FCI connector

Part No. HT-0102
Description  HT-0102 Hand Tool Manual
Download  10 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Maker  FCI-CONNECTOR [FCI connector]
Homepage  http://www.fciconnect.com
Logo FCI-CONNECTOR - FCI connector

HT-0102 Datasheet(HTML) 6 Page - FCI connector

Back Button HT-0102 Datasheet HTML 2Page - FCI connector HT-0102 Datasheet HTML 3Page - FCI connector HT-0102 Datasheet HTML 4Page - FCI connector HT-0102 Datasheet HTML 5Page - FCI connector HT-0102 Datasheet HTML 6Page - FCI connector HT-0102 Datasheet HTML 7Page - FCI connector HT-0102 Datasheet HTML 8Page - FCI connector HT-0102 Datasheet HTML 9Page - FCI connector HT-0102 Datasheet HTML 10Page - FCI connector  
Zoom Inzoom in Zoom Outzoom out
 6 / 10 page
background image
ELECTRONICS
FCI Electronics
Manual Part No. 144000-001
Issued: Date (10/24/94)
Page 6 of 10
Rev. 03/08/01 ECR V103118
Revision B
K\DCU\Manuals
III. TROUBLESHOOTING
The troubleshooting information provided in the following chart will help isolate and identify crimping problems.
Troubleshooting Chart, Male Pin Terminal
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. Bellmouth(s) is deformed or
improperly positioned on wire
barrel.
Terminal is not properly positioned
in crimping area.
Insert terminal so its shoulder is
against the terminal holder.
Reposition guide pins until proper
bellmouth(s) is achieved.
2. Pin end of terminal is bent down
Terminal is sticking in wire barrel
crimper.
Tooling is broken or cracked.
Replace wire barrel crimper as
described in Section IV, paragraph B.
3. The sides of the terminal’s wire
barrel are scored or scratched.
Wire barrel crimper is defective.
Replace wire barrel crimper as
described in Section IV paragraph B.
4. Flashings formed on the bottom
of the wire barrel are unequal or
abnormal.
Anvil is worn or broken
Replace anvil as described in
Section IV, paragraph A.
5. Insulation bulges between wire
and insulation barrels.
Wire strip length is incorrect, or wire
was inserted too far into the terminal.
Refer to Section I, Paragraph D
(specifications) for strip length
requirements.
6. Insulation bulges around
insulation barrel
Wire or insulation diameter is
incorrect for the terminal being used.
Refer to section I, paragraph D
(specifications) for correct insulation
diameter requirements.
PDM: Rev:B
Released
STATUS:
Printed: Dec 20, 2002


Html Pages

1  2  3  4  5  6  7  8  9  10 


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ]  

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Alldatasheet API   |   Link Exchange   |   Manufacturer List
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn