Electronic Components Datasheet Search
  English  ▼

Delete All
ON OFF
ALLDATASHEET.COM

X  

Preview PDF HTML

CA3277 Datasheet(PDF) 4 Page - Intersil Corporation

Part No. CA3277
Description  Dual 5V Regulator with Serial Data Buffer Interface for Microcontroller Applications
Download  8 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Maker  INTERSIL [Intersil Corporation]
Homepage  http://www.intersil.com/cda/home
Logo 

CA3277 Datasheet(HTML) 4 Page - Intersil Corporation

   
Zoom Inzoom in Zoom Outzoom out
 4 / 8 page
background image
7-42
CA3277
Applications
Other functions of the CA3277 include a Data Comparator
and Current Multiplier for use as interface buffers to transfer
serial data at higher level logic to and from a remote host
microcontroller. The OUT1 5V Standby Supply provides
power to the local microcontroller which interfaces to the
CA3277 interface buffers at a 5V logic level. As shown in
Figure 1, the DATA IN input of the Data Comparator receives
serial data referenced to the BATT voltage level. The output
of the Data Comparator is 5V CMOS compatible logic and is
connected to the RDI (remote data input) terminal of the
microcontroller. The TDO (data out) output of the microcon-
troller is connected to the Current Multiplier input of the
CA3277.
Current Multiplier - The Current Multiplier, with internal cir-
cuitry
shown
in
Figure
2,
receives
data
from
the
microcontroller in the form of an open drain or gate switched
output driving a 22K
Ω resistor load in series to the Current
Input at pin 10 (CUR IN). The input stage of the Current Mul-
tiplier is a current mirror amplifier which is internally
connected to the 5V regulated OUT1 voltage source. The
output stage of the Current Multiplier is a current mirror
amplifier referenced to GND and has an open collector
Current Output at pin 9 (CUR OUT), with a minimum drive
capability of 35mA. The Current Multiplier output load is
normally connected via resistive loading to the BATT voltage
supply level. As such, the microcontroller transmits data out
(TDO output) to the input of the CA3277 Current Multiplier
which amplifies and translates the signal back to the voltage
reference level of the BATT power supply input. When
driving a similar remote CA3277, the voltage drop from the
BATT input line switches the Data Comparator which
provides serial data to the RDI input of the remote microcon-
troller. The nominal current gain of the Current Multiplier is
100X.
The application use of the Current Multiplier is not limited to
digital serial data transfer. The Current Multiplier is an
independent function and is open to use for other purposes,
including linear signal amplification, sensor output amplifica-
tion and current controlled threshold switching. The current
output terminal, CUR OUT may be externally load-
connected to OUT1, OUT2, BATT or any other power supply
level up to the maximum ratings given for the BATT input
terminal. It is important to note that some applied uses of the
Current Multiplier may contribute significant on-chip power
dissipation. A nominal current mirror input drive of 200
µA will
provide sufficient drive to switch a 250
Ω resistor load at the
input of the data comparator. As such, the quiescent OFF
condition of the Data comparator should be in the High state.
FIGURE 1. TYPICAL APPLICATION CIRCUIT OF THE CA3277 DUAL 5V REGULATOR WITH MICROCONTROLLER AND SERIAL
DATA BUFFER INTERFACE TO A REMOTE HOST
IGN IN
BATT
CUR OUT
CUR
IN
(OUT2)
EN
DATA
OUT
IGN
OUT
CRST
RESET
OUT2
GND
OUT1
47K
0.01
µF
0.47
µF
22k
100
µF
0.1
µF
TO
+5V
DISPLAY OR
CONTROL
OUTPUT
BUS
5V MICROCONTROLLER
TDO
CONTROL
RDI SENSE
IN
RESET VDD
VSS
+5V
CMOS
MEMORY
DATA IN
UNREG
IGN IN
220
0.1
µF
330
150
µH
+5V ENABLE
+5V
C2
SUPPLY IN
(VBATT -2.9V)
6V
ERROR AMP
CONTROL
FB
FB
STANDBY
OUTPUT
SWITCHED
OUTPUT
LOW VOLT
RESET
SHTDWN
BANDGAP
OUT2
LOW VOLT
OVR-VOLT
SHTDWN
IGNITION
COMP
DATA
COMP
OUT
CURRENT
AMP
I
OVR-TEMP
SHTDWN
REF
OUT2
ENABLE
AND OUTPUT
ERROR AMP
CONTROL
AND OUTPUT
R1
C1
L1
R4
C3
C4
R5
C7
C8
CA3277
200
µF
22
µF
0.1
µF
C5
C6
NOTE:
DATA IN and CUR OUT are remote/host Serial Data Communication Buffers. Typical Remote Source
Impedance for DATA IN is 1k
Ω. Typical Remote Load for CUR OUT is 250Ω.


Html Pages

1  2  3  4  5  6  7  8 


Datasheet Download




Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ]  

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Alldatasheet API   |   Link Exchange   |   Manufacturer List
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn