Electronic Components Datasheet Search |
|
N28F001BX-B120 Datasheet(PDF) 10 Page - Intel Corporation |
|
N28F001BX-B120 Datasheet(HTML) 10 Page - Intel Corporation |
10 / 33 page 28F001BX-T28F001BX-B Table 4 28F001BX Status Register Definitions WSMS ESS ES PS VPPS R R R 7 6543210 SR7 e WRITE STATE MACHINE STATUS 1 e Ready 0 e Busy SR6 e ERASE SUSPEND STATUS 1 e Erase Suspended 0 e Erase In ProgressCompleted SR5 e ERASE STATUS 1 e Error in Block Erasure 0 e Successful Block Erase SR4 e PROGRAM STATUS 1 e Error in Byte Program 0 e Successful Byte Program SR3 e VPP STATUS 1 e VPP Low Detect Operation Abort 0 e VPP OK SR2 – SR0 e RESERVED FOR FUTURE ENHANCE- MENTS These bits are reserved for future use and should be masked out when polling the Status Register NOTES The Write State Machine Status Bit must first be checked to determine program or erase completion before the Program or Erase Status bits are checked for success If the Program AND Erase Status bits are set to ‘‘1s’’ dur- ing an erase attempt an improper command sequence was entered Attempt the operation again If VPP low status is detected the Status Register must be cleared before another program or erase operation is at- tempted The VPP Status bit unlike an AD converter does not provide continuous indication of VPP level The WSM in- terrogates the VPP level only after the program or erase command sequences have been entered and informs the system if VPP has not been switched on The VPP Status bit is not guaranteed to report accurate feedback be- tween VPPL and VPPH Erase SetupErase Confirm Commands Erase is executed one block at a time initiated by a two-cycle command sequence An Erase Setup command (20H) is first written to the Command Register followed by the Erase Confirm command (D0H) These commands require both appropriate command data and an address within the block to be erased Block preconditioning erase and verify are all handled internally by the Write State Machine invisible to the system After receiving the two-com- mand erase sequence the 28F001BX automatically outputs Status Register data when read (see Figure 10 Block Erase Flowchart) The CPU can detect the completion of the erase event by checking the WSM Status bit of the Status Register (SR7) When the Status Register indicates that erase is complete the Erase Status bit should be checked If erase error is detected the Status Register should be cleared The Command Register remains in Read Status Register Mode until further commands are is- sued to it This two-step sequence of set-up followed by execu- tion ensures that memory contents are not acciden- tally erased Also block erasure can only occur when VPP e VPPH In the absence of this high volt- age memory contents are protected against era- sure If block erase is attempted while VPP e VPPL the VPP Status bit will be set to ‘‘1’’ Erase attempts while VPPL k VPP k VPPH produce spurious results and should not be attempted Erase SuspendErase Resume Commands The Erase Suspend Command allows erase se- quence interruption in order to read data from anoth- er block of memory Once the erase sequence is started writing the Erase Suspend command (B0H) to the Command Register requests that the WSM suspend the erase sequence at a predetermined point in the erase algorithm The 28F001BX contin- ues to output Status Register data when read after the Erase Suspend command is written to it Polling the WSM Status and Erase Suspend Status bits will determine when the erase operation has been sus- pended (both will be set to ‘‘1s’’) At this point a Read Array command can be written to the Command Register to read data from blocks other than that which is suspended The only oth- er valid commands at this time are Read Status Reg- ister (70H) and Erase Resume (D0H) at which time the WSM will continue with the erase sequence The Erase Suspend Status and WSM Status bits of the Status Register will be cleared After the Erase Re- sume command is written to it the 28F001BX auto- matically outputs Status Register data when read (see Figure 11 Erase SuspendResume Flowchart) 10 |
Similar Part No. - N28F001BX-B120 |
|
Similar Description - N28F001BX-B120 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |