3/15

www.ni.com

Back to Top

Back to Top

Whether you are validating a new hardware design, monitoring conditions on a factory floor, or recording temperature changes during a scientific experiment, you need to take

measurements, visualize your data, and often log it to disk. With X Series multifunction DAQ, you can develop a user-defined measurement system by using intuitive graphical

programming software and incorporating the exact visualization, analysis, and data-logging capabilities your application requires.

Control Systems

If you need to control the temperature of a room, the speed of a motor, or the pressure of hydraulic fluids, you can use X Series DAQ hardware to connect sensors and actuators

to your computer and build the control system that meets your exact application needs. The low-latency PCI Express bus improves single-point I/O performance, and with

LabVIEW software and NI-DAQmx driver software, you can easily take sensor measurements, compare values to a setpoint, and update output signals. X Series devices also

have four counter/timers for performing quadrature encoder measurements, pulse-width modulation, pulse train generation, frequency measurements, and much more, making

them ideal for basic motor control.

Due to the inherent higher latency of USB as compared to PCI Express, National Instruments recommends that you use PCI Express or PXI Express X Series devices for

applications that require single-point control or deterministic operation.

Test Automation

X Series DAQ hardware provides analog inputs, analog outputs, hardware-timed digital I/O, and four counter/timers on a single device, making it a cost-effective option for basic

device under test characterization and test automation. With NI-DAQmx software, you can easily synchronize acquisition or generation on multiple subsystems, such as an analog

input and analog output channel. In addition, you can easily synchronize two or more X Series devices for further expansion by using a RTSI cable for PCI Express devices or

over the PXI Express backplane for PXI Express modules. It is possible to synchronize two or more USB X Series devices by exporting sample or reference clocks from the

master device to the slave device, and using external wiring.

Compatible Accessories

PCI Express and PXI Express X Series devices use either a single or dual-stack 68-pin VHDCI female connector, depending on the number of analog and digital channels on the

device. National Instruments offers several options for cables, from 0.5 to 10 m and from low-cost to high-performance with shielding. Connector blocks are available with screw

terminal, BNC, or custom connector types.

For measurements requiring signal conditioning, you can use X Series with SCXI signal conditioning modules.

You can purchase DIN-rail or panel mount kits for USB X Series devices as well as replacement power supplies and latching USB cables. See the model page for ordering

information.

Upgrading

Because X Series DAQ devices use the same NI-DAQmx driver software as NI M Series DAQ devices, upgrading is easy. In addition, PCI Express and PXI Express X Series

devices use the same VHDCI connector as PCI and PXI M Series. You can reuse your code and preserve your investment in accessories. The pinouts for X Series devices are

backward-compatible with M Series devices.

Ordering Information

For a complete list of accessories, visit the product page on ni.com.

Products

Part Number

Recommended Accessories

Part Number

NI PCIe-6320

NI PCIe-6320

Requires: 1 Cables , 1 Connector Blocks ;

781043-01

Cables: Shielded - SHC68-68-EPM Cable (2m)

**Also Available: [Unshielded]

192061-02

Connector Blocks: Spring-Screw_Terminals - SCB-68A

**Also Available: [BNC_Terminals]

782536-01

NI PCIe-6321

NI PCIe-6321

Requires: 1 Cables , 1 Connector Blocks ;

781044-01

Cables: Shielded - SHC68-68-EPM Cable (2m)

**Also Available: [Unshielded]

192061-02

Connector Blocks: Spring-Screw_Terminals - SCB-68A

**Also Available: [BNC_Terminals]

782536-01

NI PCIe-6323

NI PCIe-6323

Requires: 2 Cables , 2 Connector Blocks ;

781045-01

Connector 0:

Cables: Shielded - SHC68-68-EPM Cable (2m)

**Also Available: [Unshielded]

192061-02

Connector Blocks: Spring-Screw_Terminals - SCB-68A

**Also Available: [BNC_Terminals]

782536-01

Connector 1:

Cables: Shielded - SHC68-68-EPM Cable (2m)

**Also Available: [Unshielded]

192061-02

Connector Blocks: Spring-Screw_Terminals - SCB-68A

**Also Available: [BNC_Terminals]

782536-01

Software Recommendations