Electronic Components Datasheet Search
  English  ▼

Delete All


Preview PDF Download HTML

AT29C257 Datasheet(PDF) 1 Page - ATMEL Corporation

Part No. AT29C257
Description  256K 32K x 8 5-volt Only CMOS Flash Memory
Download  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  ATMEL [ATMEL Corporation]
Direct Link  http://www.atmel.com
Logo ATMEL - ATMEL Corporation

AT29C257 Datasheet(HTML) 1 Page - ATMEL Corporation

  AT29C257 Datasheet HTML 1Page - ATMEL Corporation AT29C257 Datasheet HTML 2Page - ATMEL Corporation AT29C257 Datasheet HTML 3Page - ATMEL Corporation AT29C257 Datasheet HTML 4Page - ATMEL Corporation AT29C257 Datasheet HTML 5Page - ATMEL Corporation AT29C257 Datasheet HTML 6Page - ATMEL Corporation AT29C257 Datasheet HTML 7Page - ATMEL Corporation AT29C257 Datasheet HTML 8Page - ATMEL Corporation AT29C257 Datasheet HTML 9Page - ATMEL Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 1 / 12 page
background image
Fast Read Access Time - 70 ns
5-Volt-Only Reprogramming
Page Program Operation
Single Cycle Reprogram (Erase and Program)
Internal Address and Data Latches for 64-Bytes
Internal Program Control and Timer
Hardware and Software Data Protection
Fast Program Cycle Times
Page (64-Byte) Program Time - 10 ms
Chip Erase Time - 10 ms
DATA Polling for End of Program Detection
Low Power Dissipation
50 mA Active Current
µA CMOS Standby Current
Typical Endurance > 10,000 Cycles
Single 5V ± 10% Supply
CMOS and TTL Compatible Inputs and Outputs
Pin-Compatible with AT29C010A and AT29C512 for Easy System Upgrades
The AT29C257 is a 5-volt-only in-system Flash programmable and erasable read only
memory (PEROM). Its 256K of memory is organized as 32,768 words by 8 bits. Manu-
factured with Atmel’s advanced nonvolatile CMOS technology, the device offers ac-
cess times to 70 ns with power dissipation of just 275 mW. When the device is dese-
lected, the CMOS standby current is less than 300
µA. The device endurance is such
that any sector can typically be written to in excess of 10,000 times.
To allow for simple in-system reprogrammability, the AT29C257 does not require high
input voltages for programming. Five-volt-only commands determine the operation of
the device. Reading data out of the device is similar to reading from a static RAM.
Reprogramming the AT29C257 is performed on a page basis; 64-bytes of data are
loaded into the device and then simultaneously programmed. The contents of the
entire device may be erased by using a 6-byte software code (although erasure before
programming is not needed).
During a reprogram cycle, the address locations and 64-bytes of data are internally
latched, freeing the address and data bus for other operations. Following the initiation
of a program cycle, the device will automatically erase the page and then program the
latched data using an internal control timer. The end of a program cycle can be de-
tected by DATA polling of I/O7. Once the end of a program cycle has been detected
a new access for a read, program or chip erase can begin.
Pin Name
A0 - A14
Chip Enable
Output Enable
Write Enable
I/O0 - I/O7
Data Inputs/Outputs
No Connect
Don’t Connect
Pin Configurations
256K (32K x 8)
5-volt Only
CMOS Flash
PLCC Top View

Html Pages

1  2  3  4  5  6  7  8  9  10  11  12 

Datasheet Download

Go To PDF Page

Link URL

Privacy Policy
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com

Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn