Electronic Components Datasheet Search
  English  ▼

Delete All
ON OFF
ALLDATASHEET.COM

X  

Preview PDF Download HTML

AS5163-HTSP Datasheet(PDF) 19 Page - ams AG

Part No. AS5163-HTSP
Description  12-Bit Automotive Angle Position Sensor
Download  37 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AMSCO [ams AG]
Direct Link  http://www.ams.com
Logo AMSCO - ams AG

AS5163-HTSP Datasheet(HTML) 19 Page - ams AG

Back Button AS5163-HTSP Datasheet HTML 15Page - ams AG AS5163-HTSP Datasheet HTML 16Page - ams AG AS5163-HTSP Datasheet HTML 17Page - ams AG AS5163-HTSP Datasheet HTML 18Page - ams AG AS5163-HTSP Datasheet HTML 19Page - ams AG AS5163-HTSP Datasheet HTML 20Page - ams AG AS5163-HTSP Datasheet HTML 21Page - ams AG AS5163-HTSP Datasheet HTML 22Page - ams AG AS5163-HTSP Datasheet HTML 23Page - ams AG Next Button
Zoom Inzoom in Zoom Outzoom out
 19 / 37 page
background image
www.austriamicrosystems.com/AS5163
Revision 2.7
18 - 36
AS5163
Datasheet - Application In form atio n
Note:
Other commands are reserved and shall not be used.
When single pin programming interface bus is in high impedance state, the logical level of the bus is held by the pull up resistor RCommunication.
Each communication begins by a condition of the bus level which is called START. This is done by forcing the bus in logical low level (done by
the programmer or AS5163 depending on the communication mode). Afterwards the bit information of the command is transmitted as shown in
Figure 14.
Figure 14. Bus Timing for the WRITE128 Command
Figure 15. Bus Timing for the READ128 Command
Table 15. OTP Commands and Communication Interface Modes
Possible Interface
Commands
Description
AS5163
Communication Mode
Command
CMD
Number of
Frames
UNBLOCK
Resets the interface
SLAVE
0x0
1
WRITE128
Writes 128 bits (user + factory settings) into the device
SLAVE
0x9
(0x1)
8
READ128
Reads 128 bits (user + factory settings) from the device
SLAVE and MASTER
0xA
9
UPLOAD
Transfers the register content into the OTP memory
SLAVE
0x6
1
DOWNLOAD
Transfers the OTP content to the register content
SLAVE
0x5
1
FUSE
Command for permanent programming
SLAVE
0x4
1
PASS2FUNC
Change operation mode from communication to operation
SLAVE
0x7
1
READ
Read related to address the user data
SLAVE and MASTER
0xB
2
WRITE
Write related to address the user data
SLAVE
0xC
1
11
00
10
00
DATA1
DATA0
DATA3
DATA2
10
00
DATA14
20*TBIT
START
IDLE
IDLE
01
10
P
00 0
DATA1
DATA0
P
00 0
DATA14
20*TBIT
DO NOT CARE
DO NOT CARE
Slave Communication Mode
Master Communication Mode
TSW
DATA3
IDLE
START


Html Pages

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36  37 


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn