 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
A428316V-25U Datasheet(PDF) 10 Page - AMIC Technology |
|
||||||||||||||||||||||||||||||
A428316V-25U Datasheet(HTML) 10 Page - AMIC Technology |
|
|
10 / 25 page  A428316 Series PRELIMINARY (August, 2002, Version 0.3) 9 AMIC Technology, Inc. Notes: 1. ICC1, ICC3, ICC4, and ICC5 depend on cycle rate. 2. ICC1 and ICC4 depend on output loading. Specified values are obtained with the outputs open. 3. An initial pause of 200 µs is required after power-up followed by any 8 RAS cycles before proper device operation is achieved. In the case of an internal refresh counter, a minimum of 8 CAS -before- RAS initialization cycles instead of 8 RAS cycles are required. 8 initialization cycles are required after extended periods of bias without clocks. 4. AC Characteristics assume tT = 2ns. All AC parameters are measured with a load equivalent to two TTL loads and 50pF, VIL (min.) ≥ GND and VIH (max.) ≤ VCC. 5. VIH (min.) and VIL (max.) are reference levels for measuring timing of input signals. Transition times are measured between VIH and VIL. 6. Operation within the tRCD (max.) limit insures that tRAC (max.) can be met. tRCD (max.) is specified as a reference point only. If tRCD is greater than the specified tRCD (max.) limit, then access time is controlled exclusively by tCAC. 7. Operation within the tRAD (max.) limit insures that tRAC (max.) can be met. tRAD (max.) is specified as a reference point only. If tRAD is greater than the specified tRAD (max.) limit, then access time is controlled exclusively by tAA. 8. Assumes three state test load (5pF and a 500 Ω Thevenin equivalent). 9. Either tRCH or tRRH must be satisfied for a read cycle. 10. tOFF (max.) defines the time at which the output achieves the open circuit condition; it is not referenced to output voltage levels. 11. tWCS, tWCH, tRWD, tCWD and tAWD are not restrictive operating parameters. They are included in the data sheet as electrical characteristics only. If tWCS ≥ tWCS (min.) and tWCH ≥ tWCH (min.), the cycle is an early write cycle and data-out pins will remain open circuit, high impedance, throughout the entire cycle. If tRWD ≥ tRWD (min.) , tCWD ≥ tCWD (min.) and tAWD ≥ tAWD (min.), the cycle is a read-modify-write cycle and the data out will contain data read from the selected cell. If neither of the above conditions is satisfied, the condition of the data out at access time is indeterminate. 12. These parameters are referenced to UCAS and LCAS leading edge in early write cycles and to WE leading edge in read-modify-write cycles. 13. Access time is determined by the longer of tAA or tCAC or tCPA. 14. tASC ≥ tCP to achieve tPC (min.) and tCPA (max.) values. |
Similar Part No. - A428316V-25U |
|
Similar Description - A428316V-25U |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
