Electronic Components Datasheet Search |
|
PT6101G Datasheet(PDF) 3 Page - Texas Instruments |
|
PT6101G Datasheet(HTML) 3 Page - Texas Instruments |
3 / 8 page Application Notes For technical support and more information, see inside back cover or visit www.ti.com/powertrends PT6100/6210/6300 Series Adjusting the Output Voltage of Power Trends’ Wide Input Range Bus ISRs The output voltage of the Power Trends’ Wide Input Range Series ISRs may be adjusted higher or lower than the factory trimmed pre-set voltage with the addition of a single external resistor. Table 1 accordingly gives the allowable adjustment range for each model for either series as V a (min) and V a (max). Adjust Up: An increase in the output voltage is obtained by adding a resistor R2, between pin 12 (Vo adjust) and pins 5-8 (GND). Adjust Down: Add a resistor (R1), between pin 12 (Vo adjust) and pins 9-11(Vout). Refer to Figure 1 and Table 2 for both the placement and value of the required resistor; either (R1) or R2 as appropriate. Notes: 1. Use only a single 1% resistor in either the (R1) or R2 location. Place the resistor as close to the ISR as possible. 2. Never connect capacitors from V o adjust to either GND or V out. Any capacitance added to the Vo adjust pin will affect the stability of the ISR. 3. Adjustments to the output voltage may place additional limits on the maximum and minimum input voltage for the part. The revised maximum and minimum input voltage limits must comply with the following requirements. Note that the minimum input voltage limits are also model dependant. V in (max) = (8 x V a)V or *30/38V, whichever is less. *Limit is 30V when inhibit function is active. PT6x0x/PT6x1x series: V in (min) = (V a + 4)V or 9V, whichever is greater. PT6x2x series: V o <10V; V in (min) = (V a + 2.0)V or 7.0V, whichever is greater. V o ≥10V; V in (min) = (V a + 2.5)V Figure 1 The values of (R1) [adjust down], and R2 [adjust up], can also be calculated using the following formulae. Ro (Va – 1.25) (R1) = Vo – Va k Ω 1.25 Ro k Ω R2 = Va – Vo Where: V o = Original output voltage V a = Adjusted output voltage R o = The resistance value fromTable 1 Table 1 ISR ADJUSTMENT RANGE AND FORMULA PARAMETERS 1Adc Rated PT6102 PT6101 PT6103 2Adc Rated PT6213 PT6212 PT6214 3Adc Rated PT6303 PT6302 PT6304 Vo (nom) 3.3 5.0 5.0 12.0 Va (min) 1.89 1.88 2.18 2.43 Va (max) 6.07 11.25 8.5 22.12 Ro (k Ω Ω Ω Ω Ω) 66.5 150.0 90.9 243.0 R2 Adjust Up C1 1 µF Ceramic (Optional) C2 100 µF (Req’d) Vo COM COM Vin + (R1) Adj Down PT6100/6200/6300 9,10,11 12 5,6,7,8 2,3,4 Vin Vo G N D Vo(adj) |
Similar Part No. - PT6101G |
|
Similar Description - PT6101G |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |