Electronic Components Datasheet Search |
|
AD6645-105PCB Datasheet(PDF) 3 Page - Analog Devices |
|
AD6645-105PCB Datasheet(HTML) 3 Page - Analog Devices |
3 / 28 page HSC-ADC-EVALB-SC/HSC-ADC-EVALB-DC Rev. 0 | Page 3 of 28 FIFO EVALUATION BOARD EASY START REQUIREMENTS • FIFO evaluation board, ADC Analyzer, and USB cable • High speed ADC evaluation board and ADC data sheet • Power supply for ADC evaluation board • Analog signal source and appropriate filtering • Low jitter clock source applicable for specific ADC evaluation, typically <1 ps rms • PC running Windows 98 (2nd ed.), Windows 2000, Windows Me, or Windows XP • PC with a USB 2.0 port recommended (USB 1.1- compatible) EASY START STEPS Note: You need administrative rights for the Windows operating systems during the entire easy start procedure. It is recommended to complete every step before reverting to a normal user mode. 1. Install ADC Analyzer from the CD provided in the FIFO evaluation kit or download the latest version on the Web. For the latest updates to the software, check the Analog Devices website at www.analog.com/hsc-FIFO. 2. Connect the FIFO evaluation board to the ADC evaluation board. If an adapter is required, insert the adapter between the ADC evaluation board and the FIFO board. If using the HSC-ADC-EVALB-SC model, connect the evaluation board to the bottom two rows of the 120-pin connector, closest to the installed IDT FIFO chip. If using an ADC with a SPI interface, remove the two 4-pin corner keys so that the third row can be connected. 3. Connect the provided USB cable to the FIFO evaluation board and to an available USB port on the computer. 4. Refer to Table 5 for any jumper changes. Most evaluation boards can be used with the default settings. 5. After verification, connect the appropriate power supplies to the ADC evaluation boards. The FIFO evaluation board is supplied with a wall mount switching power supply that provides a 6 V, 2 A maximum output. Connect the supply end to the rated 100 ac to 240 ac wall outlet at 47 Hz to 63 Hz. The other end is a 2.1 mm inner diameter jack that connects to the PCB at J301. Refer to the instructions included in the ADC data sheet for more information about the ADC evaluation board’s power supply and other requirements. 6. Once the cable is connected to both the computer and the FIFO board, and power is supplied, the USB drivers start to install. To complete the total installation of the FIFO drivers, you need to complete the new hardware sequence two times. The first Found New Hardware Wizard opens with the text message This wizard helps you install software for…Pre-FIFO 4.1 . Click the recommended install, and go to the next screen. A hardware installation warning window should then be displayed. Click Continue Anyway . The next window that opens should finish the Pre- FIFO 4.1 installation. Click Finish. Your computer should go through a second Found New Hardware Wizard, and the text message, This wizard helps you install software for…Analog Devices FIFO 4.1 , should be displayed. Continue as you did in the previous installation and click Continue Anyway . Then click Finish on the next two windows. This completes the installation. 7. (Optional) Verify in the device manager that Analog Devices, FIFO4.1 is listed under the USB hardware. 8. Apply power to the evaluation board and check the voltage levels at the board level. 9. Connect the appropriate analog input (which should be filtered with a band-pass filter) and low jitter clock signal. Make sure the evaluation boards are powered on before connecting the analog input and clock. 10. Start ADC Analyzer. 11. Choose an existing configuration file for the ADC evaluation board or create one. 12. Click Time Data in ADC Analyzer (left-most button under the menus). A reconstruction of the analog input is displayed. If the expected signal does not appear, or if there is only a flat red line, refer to the ADC Analyzer data sheet at www.analog.com/hsc-FIFO for more information. |
Similar Part No. - AD6645-105PCB |
|
Similar Description - AD6645-105PCB |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |