AD8553ARMZ-R2 datasheet(13/20 Pages) AD

Part #	AD8553ARMZ-R2

Description	1.8 V to 5 V Auto-Zero, In-Amp with Shutdown

Download	20 Pages

Scroll/Zoom	100%

Manufacturer	AD [Analog Devices]

Direct Link	http://www.analog.com

Logo

13 / 20 page

AD8553

Rev. A | Page 13 of 20

MAXIMIZING PERFORMANCE THROUGH PROPER

LAYOUT

To achieve the maximum performance of the AD8553, care

should be taken in the circuit board layout. The PC board

surface must remain clean and free of moisture to avoid leakage

currents between adjacent traces. Surface coating of the circuit

board reduces surface moisture and provides a humidity barrier,

reducing parasitic resistance on the board.

Care must be taken to minimize parasitic capacitance on Pin 1

and Pin 10 (Resistor R1 connections). Traces from Pin 1 and

Pin 10 to R1 should be kept short and symmetric. Excessive

capacitance on these pins will result in a gain error. This effect

is most prominent at low gains (G < 10).

For high impedance sources, the PC board traces from the

AD8553 inputs should be kept to a minimum to reduce input

bias current errors.

POWER SUPPLY BYPASSING

The AD8553 uses internally generated clock signals to perform

the autocorrection. As a result, proper bypassing is necessary to

achieve optimum performance. Inadequate or improper bypassing

of the supply lines can lead to excessive noise and offset voltage.

A 0.1 μF surface-mount capacitor should be connected between

the supply lines. This capacitor is necessary to minimize ripple

from the correction clocks inside the IC. For dual-supply

operation (see Figure 33), a 0.1 μF (ceramic) surface-mount

capacitor should be connected from each supply pin to ground.

For single-supply operation, a 0.1 μF surface-mount capacitor

should be connected from the supply line to ground.

All bypass capacitors should be positioned as close to the DUT

supply pins as possible, especially the bypass capacitor between

the supplies. Placement of the bypass capacitor on the back of

the board directly under the DUT is preferred.

INPUT OVERVOLTAGE PROTECTION

All terminals of the AD8553 are protected against ESD. In the

case of a dc overload voltage beyond either supply, a large

current would flow directly through the ESD protection diodes.

If such a condition should occur, an external resistor should be

used in series with the inputs to limit current for voltages

beyond the supply rails. The AD8553 can safely handle 5 mA of

continuous current, resulting in an external resistor selection of

REXT = (VIN − VS)/5 mA.

CAPACITIVE LOAD DRIVE

The output buffer, Pin 4, can drive capacitive loads up to 100 pF.

I

I– IR1

M2

VINP

M3

M4

M1

R1

(VINP –VINN)

IR1 =

R1

2I

VINN

VBIAS

M5

M6

I– IR1

I+ IR1

2IR1

C2

R2

VREF

A1

VINP –VINN

R1

2R2

VOUT =VREF +

EXTERNAL

VCC

Figure 30. Simplified AD8553 Schematic

Similar Part No. - AD8553ARMZ-R2

Manufacturer	Part #	Datasheet	Description
Analog Devices	AD8553ARMZ-REEL	334Kb / 20P	1.8 V to 5 V Auto-Zero, In-Amp with Shutdown REV. A
Analog Devices	AD8553ARMZ-REEL	383Kb / 21P	1.8 V to 5 V Auto-Zero, In-Amp with Shutdown

More results

Similar Description - AD8553ARMZ-R2

Manufacturer	Part #	Datasheet	Description
Analog Devices	AD8553	334Kb / 20P	1.8 V to 5 V Auto-Zero, In-Amp with Shutdown REV. A
	AD8563	188Kb / 15P	1.8 V to 5 V Auto-Zero, In-Amp with Shutdown Rev. PrA
	AD8553	334Kb / 20P	1.8 V to 5 V Auto-Zero, In-Amp with Shutdown Rev. A
	AD8553	383Kb / 21P	1.8 V to 5 V Auto-Zero, In-Amp with Shutdown
	AD8563	179Kb / 15P	1.8 V to 5 V Auto-Zero, In-Amp with Shutdown Rev. PrA
	ADA4051-1	620Kb / 20P	1.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp REV. B
	ADA4051-2	611Kb / 20P	1.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp REV. 0
Texas Instruments	TL16C2552	445Kb / 34P	[Old version datasheet] 1.8-V to 5-V DUAL UART WITH 16-BYTE FIFOS
	TL16C2550-Q1	997Kb / 38P	[Old version datasheet] 1.8-V to 5-V DUAL UART WITH 16-BYTE FIFOS
	TL16C2752	393Kb / 26P	[Old version datasheet] 1.8-V to 5-V DUAL UART WITH 64-BYTE FIFOS

More results

AD8553ARMZ-R2 Datasheet(PDF) 13 Page - Analog Devices

AD8553ARMZ-R2 Datasheet(HTML) 13 Page - Analog Devices

Similar Part No. - AD8553ARMZ-R2

Similar Description - AD8553ARMZ-R2

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Datasheet Download

Link URL