Electronic Components Datasheet Search |
|
RE46C107S16F Datasheet(PDF) 4 Page - Microchip Technology |
|
RE46C107S16F Datasheet(HTML) 4 Page - Microchip Technology |
4 / 9 page RE46C107 DC to DC Converter, Voltage Regulator and R&E International Piezoelectric Horn Driver A Subsidiary of Microchip Technology Inc. Product Specification © 2009 Microchip Technology Inc. DS22160A-page 4 Electrical Characteristics (continued) Limits apply at Vdd=3V, Vss=Vss2=0V, Creg=10uF, Cvo=10uF, TA=0°C to 50°C, unless otherwise noted. Typical values are at TA=27°C. Limits Parameter Symbol Test Pin Test Conditions Min Typ Max Units Voeff1 Iload= 10mA, Vdd=3V; HRNEN=0V 85 % VO Efficiency Voeff2 Iload=100uA; Vdd=3V; HRNEN=0V 75 % Low Battery Threshold Vlbat 3 LBST=Vreg 2.3 2.4 2.55 V LBST to LBOUT Propagation Delay Tplhlb 16 Vdd=2.1; LBSET Cload=5pF 10 20 us Vreg1 10 Iout<20mA; REGSEL=Vdd 3.2 3.3 3.4 V VREG Voltage Vreg2 10 Iout<20mA; REGSEL=Vss 2.9 3.0 3.1 V Vregld1 10 Iout=0 to 20mA; HRNEN=Vreg 30 50 mV VREG Load Regulation Vregld2 10 Iout=0 to 20mA; HRNEN=0V 30 50 mV Brownout Threshold Vobvt 11 Falling edge of VO 3.2 3.6 4.0 V VO-to-Brownout Margin Vobvtm 11 Vv02 -Vobvt 100 400 mV Brownout Pull down Ibt 10 VO=3.0V; Vreg=2.0V 20 40 mA Vcl1 10 REGSEL=Vdd 3.75 4 4.25 V VREG over voltage clamp Vcl2 10 REGSEL=0V 3.35 3.6 3.85 V Notes on Electrical Characteristics: 1/ DC-DC converter in high boost mode (nominal VO=10V) can draw current pulses of greater than 1 Amp and is therefore very sensitive to series resistance. Critical components of this resistance are the inductor DC resistance, the internal resistance of the battery and the resistance in the connections from the inductor to the battery, from the inductor to the LX pin and from the Vss2 pin to the battery. In order to function properly under full load at Vdd=2V, the total of the inductor and interconnect resistances should not exceed 0.3 ohm. The internal battery resistance should be no more than 0.5 ohm and a low ESR capacitor of 10uF or more should be connected in parallel with the battery to average current draw over the boost converter cycle. 2/ In the Electrical Characteristics Table, wherever a specific VO value is listed under test conditions, the VO is forced externally with the inductor disconnected and the DC-DC converter is NOT running. 3/ The brown-out threshold voltage is the VO voltage at which the regulator and horn will be disabled. At VO voltages below the brown-out threshold Vreg will be pulled to Vss. 4/ In normal operation, the regulator will provide high-side current of up to 20mA, but current sinking capability is typically under 1uA. The overvoltage clamp is intended to limit the voltage at Vreg when it is pulled up by an external source. 5/ The limits shown are 100% tested at 25C only. Test limits are guard-banded based on temperature characterization to guarantee compliance at temperature extremes. |
Similar Part No. - RE46C107S16F |
|
Similar Description - RE46C107S16F |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |