Hand Crimp Tool for 1.50mm (.591") Pitch, MX150 Crimp Terminals

Doc No: ATS-638116000

Release Date: 03-21-06

UNCONTROLLED COPY

Page 2 of 5

Revision: E

Revision Date: 10-01-09

CRIMP SPECIFICATION

Bell mouth

Conductor Brush

Terminal Series No.

mm

In.

mm

In.

33001

0.25-1.25

.010-.049

0.15-0.40

.006-.016

33012

0.25-1.25

.010-.049

0.15-0.40

.006-.016

34750

0.25-1.25

.010-.049

0.15-0.40

.006-.016

Wire brush to be below top of conductor crimp.

Bend up Bend down

Twist Roll

Terminal

Series No.

Degree

Degree

33001

33012

34750

Crimped terminals and up to 5mm of wire past the insulator

cutoff tab must freely fit in the Checking Aid, Part No. 63868-2008

Seam

Seam shall not be

open and no wire allowed

out of the crimping area

Order Separately

After crimping, the crimp profiles should measure the following:

Conductor

Wire Size

Crimp Height

Crimp Width

Profile

AWG

Terminal Series No.

AWG

mm

In.

mm

In.

18

20

22

18

0.83

1.20-1.30

.047-.051

2.05-2.25

.081-.089

X

20

0.58

1.10-1.20

.043-.047

2.05-2.25

.081-.089

X

33001

22

0.36

0.95-1.05

.037-.041

1.50-1.70

.059-.067

X

18

0.83

1.20-1.30

.047-.051

2.05-2.25

.081-.089

X

20

0.58

1.10-1.20

.043-.047

2.05-2.25

.081-.089

X

33012

22

0.36

0.95-1.05

.037-.041

1.50-1.70

.059-.067

X

18

0.83

1.20-1.30

.047-.051

2.05-2.25

.081-.089

X

20

0.58

1.10-1.20

.043-.047

2.05-2.25

.081-.089

X

34750

22

0.36

0.95-1.05

.037-.041

1.50-1.70

.059-.067

X

Insulation

Wire Size

Crimp Height

Crimp Width

Pull Force

Minimum

Terminal Series No.

AWG

mm

In.

mm

In.

N

Lb.

18

0.83

1.90-2.10

.075-.083

2.20-2.40

.086-.094

89.9

20.2

20

0.58

1.80-2.00

.071-.079

2.00-2.20

.079-.087

75.6

17.0

33001

22

0.36

1.75-1.95

.069-.077

1.80-2.00

.071-.079

49.8

11.2

18

0.83

1.90-2.10

.075-.083

2.20-2.40

.086-.094

89.9

20.2

20

0.58

1.80-2.00

.071-.079

2.00-2.20

.079-.087

75.6

17.0

33012

22

0.36

1.75-1.95

.069-.077

1.80-2.00

.071-.079

49.8

11.2

18

0.83

1.90-2.10

.075-.083

2.20-2.40

.086-.094

89.9

20.2

20

0.58

1.80-2.00

.071-.079

2.00-2.20

.079-.087

75.6

17.0

34750

22

0.36

1.75-1.95

.069-.077

1.80-2.00

.071-.079

49.8

11.2

ΤΤΤΤ

Tool Qualification Notes:

1. Pull Force should be measured with no influence from the insulation crimp.

2. The above specifications are guidelines to an optimum crimp.