Electronic Components Datasheet Search
GPFC110 Datasheet(PDF) 1 Page - SL Power Electronics
SLPOWER [SL Power Electronics]
GPFC110 Datasheet(HTML) 1 Page - SL Power Electronics
/ 2 page
• 3.1 watts/cu.in. power density
• Compact size (6.3” x 3.75” x 1.62”;
meets 1U height)
• Power factor corrected to IEC 1000-3-2 Class A
• Less than 300 μA leakage
• EMI compliance to CISPR 22, FCC Class B
• Approved to UL1950, IEC950 and
CSA 22.2 No. 950
• 2-year warranty
Compliant Model Available (G suffix)
110 Watt Global Performance Switchers
110 WATT GLOBAL PERFORMANCE SWITCHERS
All specifications are typical at nominal input, full load at 25
C unless otherwise stated
All models include built-in EMI filtering to meet the EMC requirements below.
85-264 Vac, 47-63 Hz single phase.
Maximum input current 2.3 A at 90 Vac, 60 Hz with full rated load. Input cur-
rent harmonic content meets the requirements of IEC1000-3-2.
25 ms minimum from loss of ac input at full load, nominal line (115 Vac).
110 W fan cooled, 75 W convection. Peak ratings are for 60 s maximum dura-
tion, 10% duty cycle.
Total regulation is the maximum deviation from the nominal voltage for all
steady-state loading conditions.
Fully protected against short circuit and output overload. Short circuit protec-
tion is cycling type power limit. Recovery after fault is automatic.
0.5% rms, 1% pk-pk, 20 MHz Bandwidth, differential mode. Measured with
noise probe directly across output terminals of the power supply.
500 μs typical response time for return to within 0.5% of final value for a 50%
load step change, ∆i/∆ t< 0.2 A/μs. Maximum voltage deviation is 3.5%. Load
must not go below stated minimum.
Provided as a standard feature. Capable of compensating for 0.25 V total of
cabling losses in voltage. Open sense lead protection.
OVP crowbar reduces output voltage below nominal rating in less than 50 ms.
Voltage Adjustment: Main output ±5%.
Internal ac fuse provided on all models. Fuse does not blow on overload or
short circuit—fuse blows only if catastrophic failure occurs in the unit.
RF Field Susceptibility
Line Frequency Harmonics
EN55022 Class B; FCC Class B
EN61000-4-2, 6 kV contact, 8 kV air
EN61000-4-3, 3 V/meter
EN61000-4-4, 2 kV, 5 kHz
EN61000-4-5, 1 kV diff., 2 kV com.
EN61000-3-2 Class A
Inrush 240 Vac is less than 37 A, averaged over the first ac half-cycle under cold
start conditions. Limiting provided by internal thermistors.
An additional output, same as Vout, suitable for powering a dc fan is included in all
models. The output is protected by an internal resistor in the event of an overload.
TTL or CMOS compatible output goes low (<0.5 V) 8 ms before output voltage
drops more than 4% below nominal voltage upon loss of ac power. The signal is
factory set to trip when input power can no longer sustain the output.
0.03%/°C typical on all outputs.
Designed for 0 to 50°C operation at full rated output power; derate output current
and total output power by 2.5% per °C above 50°C. See Environmental and Pack-
aging Specifications on the next page.
Commercial Safety Approvals
All models are approved to UL1950, CSA22.2 No. 950-95, IEC950, EN60950. CB
certificate available. Exceeds FCC and CISPR22 Class B conducted emissions
marked to LVD
Does ALLDATASHEET help your business so far?
[ DONATE ]
All Rights Reserved©
| English :
| Chinese :
| German :
| Japanese :
| Korean :
| Spanish :
| French :
| Italian :
| Polish :
| Vietnamese :