Electronic Components Datasheet Search |
|
AD73360ASU Datasheet(PDF) 17 Page - Analog Devices |
|
AD73360ASU Datasheet(HTML) 17 Page - Analog Devices |
17 / 35 page REV. A AD73360 –17– Table XIII. Control Register G Description 76543210 SEEN RMOD CH6 CH5 CH4 CH3 CH2 CH1 Bit Name Description 0 CH1 Channel 1 Select 1 CH2 Channel 2 Select 2 CH3 Channel 3 Select 3 CH4 Channel 4 Select 4 CH5 Channel 5 Select 5 CH6 Channel 6 Select 6 RMOD Reset Analog Modulator 7 SEEN Enable Single-Ended Input Mode Table XIV. Control Register H Description 76543210 INV TME CH6 CH5 CH4 CH3 CH2 CH1 Bit Name Description 0 CH1 Channel 1 Select 1 CH2 Channel 2 Select 2 CH3 Channel 3 Select 3 CH4 Channel 4 Select 4 CH5 Channel 5 Select 5 CH6 Channel 6 Select 6 TME Test Mode Enable 7 INV Enable Invert Channel Mode CONTROL REGISTER G CONTROL REGISTER H REGISTER BIT DESCRIPTIONS Control Register A CRA:0 Data/Program Mode. This bit controls the operating mode of the AD73360. If CRA:1 is 0, then a 0 in this bit places the part in Program Mode. If CRA:1 is 0, then a 1 in this bit places the part in Data Mode. CRA:1 Mixed Mode. If this bit is a 0, then the operating mode is determined by CRA:0. If this bit is a 1, then the part operates in Mixed Mode. CRA:2 Reserved. This bit is reserved and should be programmed to 0 to ensure correct operation. CRA:3 SPORT Loop Back. This is a diagnostic mode. This bit should be set to 0 to ensure correct operation. CRA:4–6 Device Count Bits. These bits tell the AD73360 how many devices are used in a cascade. All devices in the cascade should be programmed to the same value ensure correct operation. See Table XVIII. CRA:7 Reset. Writing a 1 to this bit will initiate a software reset of the AD73360. Control Register B CRB:0–1 Decimation Rate. These bits are used to set the decimation of the AD73360. See Table VII. CRB:2–3 Serial Clock Divider. These bits are used to set the serial clock frequency. See Table VI. CRB:4–6 Master Clock Divider. These bits are used to set the Master Clock Divider ratio. See Table V. CRB:7 Control Echo Enable. Setting this bit to a 1 will cause the AD73360 to write out any control words it receives. This is used as a diagnostic mode. This bit should be set to 0 for correct operation in Mixed Mode or Data Mode. |
Similar Part No. - AD73360ASU |
|
Similar Description - AD73360ASU |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |