Electronic Components Datasheet Search
  English  ▼

Delete All
ON OFF
ALLDATASHEET.COM

X  

Preview PDF Download HTML

AD28MSP01 Datasheet(PDF) 4 Page - Analog Devices

Part No. AD28MSP01
Description  PSTN Signal Port
Download  28 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Maker  AD [Analog Devices]
Homepage  http://www.analog.com
Logo 

AD28MSP01 Datasheet(HTML) 4 Page - Analog Devices

 
Zoom Inzoom in Zoom Outzoom out
 4 / 28 page
background image
AD28msp01
REV. A
–4–
The output of the ADC is transferred to the AD28msp01’s se-
rial port (SPORT) for transmission to the host DSP processor.
D/A CONVERSION
The D/A conversion circuitry of the AD28msp01 consists of a
sigma-delta digital-to-analog converter (DAC) and a differential
output amplifier.
DAC
The DAC consists of an anti-imaging low-pass filter, an interpo-
lation filter, a digital sigma-delta modulator, and an analog
smoothing filter. These filters have the same characteristics as
the ADC’s anti-aliasing filter and decimation filter.
The DAC receives 16-bit samples from the host DSP processor
via AD28msp01’s SPORT. If the host processor fails to write a
new value to the serial port, the existing (previous) data is read
again. The data stream is filtered first by the DAC’s anti-
imaging low-pass filter and then by the interpolation filter. The
output of the interpolation filter is fed to the DAC’s digital
sigma-delta modulator, which converts the 16-bit data to 1-bit
samples. The output of the sigma-delta modulator is fed to the
AD28msp01’s analog smoothing filter where it is converted into
a low-pass filtered, analog voltage.
Anti-lmaging Low-Pass Filter
The anti-imaging low-pass filter filters the 7.2 kHz, 8.0 kHz, or
9.6 kHz data stream form the SPORTs, and raises the sampling
rate to 28.8 kHz, 32.0 kHz, or 38.4 kHz.
The anti-imaging low-pass filter can be bypassed by setting the
appropriate bit in Control Register 1. This results in a gain
change. If the filter is bypassed, the signal must be scaled by the
following multipliers to achieve normal levels: 2.046 for 9.6 kHz,
0.987 for 8.0 kHz, and 0.647 for 7.2 kHz.
When the filter is bypassed, the host DSP must be able to trans-
mit data at the 28.8/32.0/38.4 kHz rates. In this case, re-
sampling interpolation should be disabled because of
insufficient bandwidth to transmit both ADC and resampled
data to the SPORT.
Interpolation Filter
The interpolation filter contains is a sinc
4 digital filter which
raises the sampling rate to 1.7280 MHz by interpolating be-
tween the samples. These 16-bit samples are then processed by
the digital sigma-delta modulator which noise-shapes the data
stream and reduces the sample width to a single bit stream.
Analog Smoothing Filter
The AD28msp01’s analog smoothing filter consists of a 2nd-
order Sallen-Key continuous-time filter and a 3rd-order switched
capacitor filter. The Sallen-Key filter has a 3 dB point at
approximately 80 kHz.
The analog smoothing filter converts the 1.7280 MHz bit
stream output of the sigma-delta modulator into a low-pass
filtered, differential analog signal.
Differential Output Amplifier
The differential output amplifier produces the AD28msp01’s
analog output (VOUTP, VOUTN). It can drive loads of 2 k
Ω or
greater and has a maximum differential output voltage swing of
6.312 V peak-to-peak. The output signal is dc biased to the
AD28msp01’s on-chip voltage reference (2.5 V nominal) and
can be ac coupled directly to a load or dc coupled to an external
amplifier. Refer to “Analog Output” in the “Design Consider-
ations” section of this data sheet for more information.
The VOUTP and VOUTN outputs must be used as differential out-
puts; do not use either as a single-ended output.
SERIAL PORT
The AD28msp01 includes a full-duplex synchronous serial port
(SPORT) used to communicate with a host processor. The
SPORT is used to read and write all data and control registers
in the AD28msp01. The SPORT transfers 16-bit words, MSB
first, at a serial clock rate of 1.7280 MHz.
When the AD28msp01 exits reset, both the analog circuitry and
the digital circuitry are powered down. The serial port will not
transmit data to the host until the host sets the digital power-
down bit (PWDD) to 1 in Control Register 1. All control regis-
ters should be initialized before this bit is set.
The SPORT is configured for an externally generated receive
frame sync (SDIFS), an internally generated serial clock
(SCLK), and an internally generated transmit frame sync
(SDOFS). The host processor should be configured for an ex-
ternal serial clock and receive frame sync and an internal trans-
mit frame sync.
DSP Processor Interface
The AD28msp01-to-host processor interface is shown in
Figure 2.
SDO
SDOFS
SCLK
CS
SDI
SDIFS
SERIAL DATA RECEIVE
RECEIVE FRAME SYNC
SERIAL CLOCK
FLAG
SERIAL DATA TRANSMIT
TRANSMIT FRAME SYNC
DSP PROCESSOR
AD28msp01
Figure 2. AD28msp01-to-DSP Processor Interface
The AD28msp01’s chip select (CS) must be held high to enable
SPORT operation. CS can be used to 3-state the SPORT pins
and disable communication with the host processor.
To use the ADSP-2101 or ADSP-2111 as host DSP processor
for the AD28msp01, refer to Figure 3.
Note that the ADSP-2101’s SPORT0 communicates with the
AD28msp01’s SPORT while the ADSP-2101’s Flag Output
(FO) is used to signal the AD28msp01’s CS input. SPORT1 on
the ADSP-2101 must be configured for flags and interrupts in
this system.
SDO
SDOFS
SCLK
CS
SDI
SDIFS
DR0
RFS0
SCLK0
FO
DT0
TFS0
ADSP-2101
AD28msp01
Figure 3. AD28msp01-to-ADSP-2101 Interface
Figure 4 shows an ADSP-2101 assembly language program that
initializes the AD28msp01 and implements a digital loopback
through the processor.


Html Pages

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28 


Datasheet Download




Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ]  

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Alldatasheet API   |   Link Exchange   |   Manufacturer List
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn