 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
IG120-12W Datasheet(PDF) 2 Page - MicroPower Direct, LLC |
|
||||||||||||||||||||||||||||||
IG120-12W Datasheet(HTML) 2 Page - MicroPower Direct, LLC |
|
|
2 / 2 page  Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit Model Number Input (Supply) Output 1 Output 2 Output Load Regulation (%) Maximum Capacitive Load (µF) Fuse Rating Slow-Blow (mA) Voltage (VDC) Voltage (VDC) Current (mA Max) Current (mA, Min) Voltage (VDC) Current (mA Max) Current (mA, Min) Nom. Range Min. Nom. Max. Min. Nom. Max. IG120-12 12 11.6 - 12.4 14.0 15.0 16.0 80.0 0.0 -7.0 -9.0 -10.0 40.0 0.0 12 470 1,000 IG120-12W 12 9.0 - 15.0 14.0 15.0 16.0 100.0 0.0 -7.0 -8.0 -9.0 80.0 0.0 12 470 1,000 IG120-15 15 14.5 - 15.5 14.0 15.0 16.0 80.0 0.0 -7.0 -8.7 -10.0 40.0 0.0 18 470 1,000 IG136-15 15 14.5 - 15.5 16.5 17.0 18.0 80.0 0.0 -7.0 -8.7 -10.0 40.0 0.0 18 470 1,000 IG120-24 24 23.3 - 24.7 14.0 15.0 16.0 80.0 0.0 -7.0 -9.0 -10.0 40.0 0.0 12 470 1,000 Pin Function 1+Vin 2 Gnd 5 Vout 2 6 Common 7 Vout 1 Typical Connection yp Notes: 1. Line regulation for model IG120-12W is given for a VIN change of 25%. 2. Load regulation is measured from 10% load to full load. Load regulation is specified for the primary output (output 1). Load regulation of output 2 may vary slightly. 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. If output 2 is not used, it should be left open. 5. A short circuit fault that lasts over 10 minutes could damage the unit due to an over temperature fault. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Connection Notes: 1. For model IG120-24, C1 is a 100 µF/65V. 2. Capacitors C1, C2 and C3 should be mounted as close to the unit as possible. To ensure peak gate current, these capacitors should have a low ESR. 3. The trace (or wire) between the DC/DC and the driver circuit should be as short as possible. 4. The average output power of the driver circuit must be lower than output power of the DC/DC. The IG100 series is designed to operate with the IGD962 IGBT driver. Model Selection Guide Mechanical Dimensions Pin Connections MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com www.micropowerdirect.com |
Similar Part No. - IG120-12W |
|
Similar Description - IG120-12W |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
