 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
CY14B101P-SFXI Datasheet(PDF) 5 Page - Cypress Semiconductor |
|
||||||||||||||||||||||||||||||
CY14B101P-SFXI Datasheet(HTML) 5 Page - Cypress Semiconductor |
|
|
5 / 36 page  CY14B101P Document Number: 001-44109 Rev. *M Page 5 of 36 Figure 2 shows the proper connection of the storage capacitor (VCAP) for AutoStore operation. See DC Electrical Characteristics on page 24 for the size of the VCAP. Figure 2. AutoStore Mode Software STORE Operation Software STORE allows the user to trigger a STORE operation through a special SPI instruction. STORE operation is initiated by executing STORE instruction irrespective of whether a write has been performed since the last NV operation. A STORE cycle takes tSTORE time to complete, during which all the memory accesses to nvSRAM are inhibited. The RDY bit of the Status Register or the HSB pin may be polled to find the Ready/Busy status of the nvSRAM. After the tSTORE cycle time is completed, the SRAM is activated again for read and write operations. Hardware STORE and HSB Pin Operation The HSB pin in CY14B101P is used to control and acknowledge STORE operations. If no STORE/RECALL is in progress, this pin can be used to request a Hardware STORE cycle. When the HSB pin is driven LOW, the CY14B101P conditionally initiates a STORE operation after tDELAY duration. A STORE cycle starts only if a write to the SRAM was performed since the last STORE or RECALL cycle. Reads and writes to the memory are inhibited for tSTORE duration or as long as HSB pin is LOW. The HSB pin also acts as an open drain driver (internal 100 k weak pull-up resistor) that is internally driven LOW to indicate a busy condition when the STORE (initiated by any means) is in progress. Note After each Hardware and Software STORE operation HSB is driven HIGH for a short time (tHHHD) with standard output high current and then remains HIGH by an internal 100 k pull-up resistor. Note For successful last data byte STORE, a hardware store should be initiated atleast one clock cycle after the last data bit D0 is received. Upon completion of the STORE operation, the nvSRAM memory access is inhibited for tLZHSB time after HSB pin returns HIGH. The HSB pin must be left unconnected if not used. RECALL Operation A RECALL operation transfers the data stored in the nonvolatile QuantumTrap elements to the SRAM. In CY14B101P, a RECALL may be initiated in two ways: Hardware RECALL, initiated on power-up; and Software RECALL, initiated by a SPI RECALL instruction. Internally, RECALL is a two step procedure. First, the SRAM data is cleared. Next, the nonvolatile information is transferred into the SRAM cells. All memory accesses are inhibited while a RECALL cycle is in progress. The RECALL operation does not alter the data in the nonvolatile elements. Hardware RECALL (Power-Up) During Power-up, when VCC crosses VSWITCH, an automatic RECALL sequence is initiated, which transfers the content of nonvolatile memory on to the SRAM. A Power-up RECALL cycle takes tFA time to complete and the memory access is disabled during this time. HSB pin is used to detect the Ready status of the device. Software RECALL Software RECALL allows the user to initiate a RECALL operation to restore the content of nonvolatile memory on to the SRAM. In CY14B101P, this can be done by issuing a RECALL instruction in SPI. A Software RECALL takes tRECALL time to complete during which all memory accesses to nvSRAM are inhibited. The controller must provide sufficient delay for the RECALL operation to complete before issuing any memory access instructions. Disabling and Enabling AutoStore If the application does not require the AutoStore feature, it can be disabled in CY14B101P by using the ASDISB instruction. If this is done, the nvSRAM does not perform a STORE operation at power-down. AutoStore can be re-enabled by using the ASENB instruction. However, these operations are not nonvolatile and if the user needs this setting to survive the power cycle, a STORE operation must be performed following AutoStore Disable or Enable operation. Note CY14B101P comes from the factory with AutoStore Enabled and with 0x00 written in all cells. Note If AutoStore is disabled and VCAP is not required, then the VCAP pin must be left open. The VCAP pin must never be connected to ground. The Power-Up RECALL operation cannot be disabled in any case. 0.1 uF VCC VCAP CS VCAP VSS VCC |
Similar Part No. - CY14B101P-SFXI |
|
Similar Description - CY14B101P-SFXI |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
