Electronic Components Datasheet Search |
|
PTEA415050 Datasheet(PDF) 8 Page - Texas Instruments |
|
|
PTEA415050 Datasheet(HTML) 8 Page - Texas Instruments |
8 / 14 page PTEA415050 SLTS291B – JULY 2008 – REVISED NOVEMBER 2010 www.ti.com Using the Remote On/Off Function on the PTEA415050 DC/DC Converter For applications requiring output voltage On/Off control, the PTEA415050 DC/DC converter incorporate a Remote On/Off control (pin 2). This feature can be used to switch the module off without removing the applied input source voltage. When placed in the Off state, the standby current drawn from the input source is typically reduced to 3 mA. Negative Output Enable (NEN) Models using the negative enable option, the Remote On/Off (pin 2) control must be driven to a logic low voltage for the converter to produce an output. This is accomplished by either permanently connecting pin 2 to –VI (pin 3), or driving it low with an external control signal. Table 2 shows the input requirements of pin 2 for those modules with the NEN option. Table 2. On/Off Control Requirements for Negative Enable PARAMETER MIN TYP MAX UNITS VIH Disable 2.4 20 V VIL Enable –0.2 0.8 Vo/c Open-Circuit 9 15 II Pin 2 at –VI –0.75 mA Positive Output Enable (PEN) For those models with the positive enable (PEN) option, leaving pin 2 open circuit, (or driving it to an equivalent logic high voltage), will enable the converter output. This allows the module to produce an output voltage whenever a valid input source voltage is applied to +VI with respect to –VI. If a logic-low signal is then applied to pin 2 the converter output is disabled. Table 3 gives the input requirements of pin 2 for modules with the PEN option. Table 3. On/Off Control Requirements for Positive Enable PARAMETER MIN TYP MAX UNITS VIH Enable 4.5 20 V VIL Disable –0.2 0.8 Vo/c Open-Circuit 5 7 II Pin 2 at –VI –0.5 mA Notes: 1. The Remote On/Off control uses –VI (pin 3) as its ground reference. All voltages are with respect to –VI. 2. An open-collector device (preferably a discrete transistor) is recommended. A pull-up resistor is not required. If one is added the pull-up voltage should not exceed 20 V. Caution: Do not use a pull-resistor to +VI (pin 1). The remote On/Off control has a maximum input voltage of 20 V. Exceeding this voltage will overstress, and possibly damage, the converter. 3. The Remote On/Off pin may be controlled with devices that have a totem-pole output. This is provided the output high level voltage (VOH) meets the module's minimum VIH specified in Table 2. If a TTL gate is used, a pull-up resistor may be required to the logic supply voltage. 4. The converter incorporates an undervoltage lockout (UVLO). The UVLO keeps the converter off until the input voltage is close to the minimum specified operating voltage. This is regardless of the state of the Remote On/Off control. Consult the product specification for the UVLO input voltage thresholds. 8 Copyright © 2008–2010, Texas Instruments Incorporated Product Folder Link(s): PTEA415050 |
Similar Part No. - PTEA415050 |
|
Similar Description - PTEA415050 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |