EVALUATION BOARD/KIT IMPORTANT NOTICE

Silicon Laboratories Inc. and its affiliated companies ("Silicon Labs") provides the enclosed evaluation board/kit to the user ("User") under the following conditions:

This evaluation board/kit ("EVB/Kit") is intended for use for ENGINEERING DEVELOPMENT, TESTING, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not a finished

end-product fit for general consumer use. ANY OTHER USE, RESALE, OR REDISTRIBUTION FOR ANY OTHER PURPOSE IS STRICTLY PROHIBITED. This EVB/Kit is not intended to

be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end

products that incorporate such semiconductor components or circuit boards. As such, persons handling this EVB/Kit must have electronics training and observe good engineering practice

standards. As a prototype not available for commercial reasons, this EVB/Kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility,

restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.

Should this EVB/Kit not meet the specifications indicated in the User's Guide, the EVB/Kit may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING

WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SILICON LABS TO USER, IS USER'S SOLE REMEDY, AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED,

IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY, NONINFRINGEMENT, DESIGN, WORKMANSHIP, OR FITNESS FOR ANY PARTICULAR PUR-

POSE.

User assumes all responsibility and liability for proper and safe handling of the EVB/Kit. Further, User indemnifies Silicon Labs from all claims arising from User's handling or use of the

EVB/Kit. Due to the open construction of the EVB/Kit, it is User's responsibility to take any and all appropriate precautions with regard to electrostatic discharge.

EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CON-

SEQUENTIAL DAMAGES.

Neither Silicon Labs nor User is obligated to perform any activities or conduct any business as a consequence of using the EVB/Kit, and neither party is entitled to any form of exclusivity

with respect to the EVB/Kit.

Silicon Labs assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein.

Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the EVB/Kit. This notice contains important safety information

about temperatures and voltages. For additional environmental and/or safety information, please contact a Silicon Labs application engineer or visit www.silabs.com/support/quality.

No license is granted under any patent right or other intellectual property right of Silicon Labs covering or relating to any machine, process, or combination in which the EVB/Kit or any of its

components might be or are used.

User's use of this EVB/Kit is conditioned upon acceptance of the foregoing conditions. If User is unwilling to accept these conditions, User may request a refund and return the EVB/Kit to

Silicon Labs in its original condition, unopened, with the original packaging and all documentation to:

Mailing Address:

400 W. Cesar Chavez

Austin, TX 78701

Copyright © 2012 by Silicon Laboratories

Rev. 0.2 7/12

A. Install Software

B. Hardware Setup (Steps 1, 4, and 5 Only Apply to Enhanced Development Kits)

C. Documentation

1

2

Click the large Download Button to

initiate the Precision32 web install.

Navigate to the Precision32

software download website.

3

Start the Installer and allow it to run in

the background. Advance to Step 4 while

the Precision32 Development Suite and

AppBuilder are being installed.

www.silabs.com/

32bit-software

1

Connect the USB Debug Adapter

ribbon cable to the MCU card.

2

Connect the USB Debug Adapter to the

PC using the standard USB cable.

I/O card

MCU card

4

5

If Enhanced DK, apply power to the UDP

Motherboard using 1 of 4 power options,

Power Options

1: 9 V Universal Adapter (J20)

2: Standard USB (J16)

3: Mini USB (J1)

4: 6 V Battery Pack (J11)

then set power switch (S3) to the ON Position.

If Development Kit, apply power to the

MCU Card using 1 of 2 power options.

Power Options

1: Mini USB – For USB MCUs

2: 9 V Universal Adapter – For Non-USB

MCUs

If Enhanced DK, update the motherboard

firmware using the UDP Motherboard

Firmware Update Utility.

www.silabs.com/udp

MCU card

3

2

1

4

12

Note: If Enhanced DK, the MCU Card is powered

from the motherboard.

3

6

If Enhanced DK, connect the MCU card

and I/O card to the UDP Motherboard.

1

Download the User’s Guide for Each

Board in the Development Kit.

Where to Find Documentation

Data Sheet:

www.silabs.com/32bit-mcu

Reference Manual:

www.silabs.com/32bit-mcu

Hardware User's Guide:

www.silabs.com/32bit-mcu

OR www.silabs.com/udp

Application Notes:

www.silabs.com/32bit-mcu

Software Development Kit Documentation:

C:\Silabs\32bit\si32-{revision}\Documentation\si32Hal.chm

Quality Documents:

www.silabs.com/quality