Electronic Components Datasheet Search |
|
X9119TV14 Datasheet(PDF) 3 Page - Intersil Corporation |
|
X9119TV14 Datasheet(HTML) 3 Page - Intersil Corporation |
3 / 17 page 3 FN8162.4 July 9, 2008 Applications Circuit Level • Vary the gain of a voltage amplifier • Provide programmable DC reference voltages for comparators and detectors • Control the volume in audio circuits • Trim out the offset voltage error in a voltage amplifier circuit • Set the output voltage of a voltage regulator • Trim the resistance in Wheatstone bridge circuits • Control the gain, characteristic frequency and Q-factor in filter circuits • Set the scale factor and zero point in sensor signal conditioning circuits • Vary the frequency and duty cycle of timer ICs • Vary the DC biasing of a pin diode attenuator in RF circuits • Provide a control variable (I, V, or R) in feedback circuits System Level • Adjust the contrast in LCD displays • Control the power level of LED transmitters in communication systems • Set and regulate the DC biasing point in an RF power amplifier in wireless systems • Control the gain in audio and home entertainment systems • Provide the variable DC bias for tuners in RF wireless systems • Set the operating points in temperature control systems • Control the operating point for sensors in industrial systems • Trim offset and gain errors in artificial intelligent systems Pinout X9119 (14 LD TSSOP) TOP VIEW Bus Interface Pins SERIAL DATA INPUT/OUTPUT (SDA) The SDA is a bidirectional serial data input/output pin for a 2-wire slave device and is used to transfer data into and out of the device. It receives device address, opcode, wiper register address and data sent from an 2-wire master at the rising edge of the serial clock SCL, and it shifts out data after each falling edge of the serial clock SCL. It is an open drain output and may be wire-ORed with any number of open drain or open collector outputs. An open drain output requires the use of a pull-up resistor. For selecting typical values, refer to the guidelines for calculating typical values on the bus pull-up resistors graph. SERIAL CLOCK (SCL) This input is used by 2-wire master to supply 2-wire serial clock to the X9119. DEVICE ADDRESS (A2–A0) The Address inputs are used to set the least significant 3 bits of the 8-bit slave address. A match in the slave address serial data stream must be made with the Address input in order to initiate communication with the X9119. A maximum of 8 devices may occupy the 2-wire serial bus. HARDWARE WRITE PROTECT INPUT (WP) The WP pin when LOW prevents nonvolatile writes to the Data Registers. Potentiometer Pins RH, RL The RH and RL pins are equivalent to the terminal connections on a mechanical potentiometer. VCC RL VSS 1 2 3 4 5 6 7 8 14 13 12 11 10 9 NC RW A2 A1 RH A0 NC SDA NC SCL WP Pin Assignments PIN NUMBER PIN NAME FUNCTION 1, 3, 10 NC No Connect 2 A0 Device Address for 2-wire bus 4 A2 Device Address for 2-wire bus 5 SCL Serial Clock for 2-wire bus 6 SDA Serial Data Input/Output for 2-wire bus 7VSS System Ground 8WP Hardware Write Protect 9 A1 Device Address for 2-wire bus 11 RW Wiper terminal of the Potentiometer 12 RH High terminal of the Potentiometer 13 RL Low terminal of the Potentiometer 14 VCC System Supply Voltage X9119 |
Similar Part No. - X9119TV14 |
|
Similar Description - X9119TV14 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |