Electronic Components Datasheet Search
  English  ▼

Delete All
ON OFF
ALLDATASHEET.COM

X  

Preview PDF HTML

STK4171V Datasheet(PDF) 6 Page - Sanyo Semicon Device

Part No. STK4171V
Description  AF Power Amplifier (Split Power Supply) (40W 40W min, THD = 0.08%)
Download  8 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Maker  SANYO [Sanyo Semicon Device]
Homepage  http://www.ssdc-jp.com/eng/
Logo 

STK4171V Datasheet(HTML) 6 Page - Sanyo Semicon Device

   
Zoom Inzoom in Zoom Outzoom out
 6 / 8 page
background image
STK4171V
No. 2136—6/8
C3, C4
Input filter capacitors
• A filter formed with R5 or R6 can be used to reduce noise at high frequencies.
C5, C6
Input coupling capacitors
• Used to block DC current. When the reactance of the capacitor increases at low frequencies, the dependence of 1/f noise on signal source
resistance causes the output noise to worsen. It is better to decrease the reactance.
• To reduce the pop noise at the time of application of power, it is effective to increase C5, C6 that fix the time constant on the input side and
to decrease C9, C10 on the NF side.
C9, C10
NF capacitors
• These capacitors fix the low cutoff frequency as shown below.
To provide the desired voltage gain at low frequencies, it is better to increase C9. However, do not increase C9 more than needed because
the pop noise level becomes higher at the time of application of power.
C19
Decoupling capacitor
• Used to eliminate the ripple components that mix into the input side from the power line (+VCC).
C15, C16
Bootstrap capacitors
• When the capacitor value is decreased, the distortion is liable to be higher at low frequencies.
C17, C18
Oscillation blocking capacitors
• Must be inserted as close to the IC power supply pins as possible so that the power supply impedance is decreased to operate the IC stably.
• Electrolytic capacitors are recommended for C17, C18.
C20
Capacitor for ripple filter
• Capacitor for the TR12-used ripple filter in the IC system
C13
Oscillation blocking capacitor
• A polyester film capacitor, being excellent in temperature characteristic, frequency characteristic, is recommended for C13.
R5, R6
Resistors for input filter
R3, R4
Input bias resistors
• Used to bias the input pin potential to zero. These resistors fix the input impedance practically.
R7, R9
(R8, R10)
These resistors fix voltage gain VG.
It is recommended to use R7 (R8) = 560
Ω, R9 (R10) = 56kΩ for VG = 40dB.
• To adjust VG, it is desirable to change R7 (or R8).
• When R7 (or R8) is changed to adjust VG, R3 (=R4) =R9 (=R10) must be set to ensure VN balance.
R11, R20
(R12, R21)
Bootstrap resistors
• The quiescent current is set by these resistors 3.3k
Ω + 3.3kΩ. It is recommended to use this resistor value.
R15
Resistor for ripple filter
• (Limiting resistor for predriver TR at the time of load short)
R14
Used to ensure plus/minus balance at the time of clip.
R18, R19
Resistor for ripple filter
• When muting TR13 is turned ON, current flows from ground to -VCC through TR 13. It is recommended to use 1kΩ (1W) + 1kΩ (1W)
allowing for the power that may be dissipated on that occasion.
R24, R25
Oscillation blocking resistors
R22, R23
Oscillation blocking resistors
L1, L2
Oscillation blocking coils
f
L
1
2
π C9 R7
⋅⋅
---------------------------
=
[Hz]


Html Pages

1  2  3  4  5  6  7  8 


Datasheet Download




Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ]  

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Alldatasheet API   |   Link Exchange   |   Manufacturer List
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn