11

Component Selection Guidelines

Charge Pump Capacitor Selection

A capacitor across pins CT1 and CT2 is required to create

the proper bias voltage for the ISL6526 when operating the

IC from 3.3V. Selecting the proper capacitance value is

important so that the bias current draw and the current

required by the MOSFET gates do not overburden the

capacitor. A conservative approach is presented in the

following equation.

Output Capacitor Selection

An output capacitor is required to filter the output and supply

the load transient current. The filtering requirements are a

function of the switching frequency and the ripple current.

The load transient requirements are a function of the slew

rate (di/dt) and the magnitude of the transient load current.

These requirements are generally met with a mix of

capacitors and careful layout.

Modern digital ICs can produce high transient load slew

rates. High frequency capacitors initially supply the transient

and slow the current load rate seen by the bulk capacitors.

The bulk filter capacitor values are generally determined by

the ESR (Effective Series Resistance) and voltage rating

requirements rather than actual capacitance requirements.

High frequency decoupling capacitors should be placed as

close to the power pins of the load as physically possible. Be

careful not to add inductance in the circuit board wiring that

could cancel the usefulness of these low inductance

components. Consult with the manufacturer of the load on

specific decoupling requirements.

Use only specialized low-ESR capacitors intended for

switching-regulator applications for the bulk capacitors. The

bulk capacitor’s ESR will determine the output ripple voltage

and the initial voltage drop after a high slew-rate transient. An

aluminum electrolytic capacitor’s ESR value is related to the

case size with lower ESR available in larger case sizes.

However, the Equivalent Series Inductance (ESL) of these

capacitors increases with case size and can reduce the

usefulness of the capacitor to high slew-rate transient loading.

Unfortunately, ESL is not a specified parameter. Work with

your capacitor supplier and measure the capacitor’s

impedance with frequency to select a suitable component. In

most cases, multiple electrolytic capacitors of small case size

perform better than a single large case capacitor.

Output Inductor Selection

The output inductor is selected to meet the output voltage

ripple requirements and minimize the converter’s response

time to the load transient. The inductor value determines the

converter’s ripple current and the ripple voltage is a function

of the ripple current. The ripple voltage and current are

approximated by the following equations:

Increasing the value of inductance reduces the ripple current

and voltage. However, the large inductance values reduce

the converter’s response time to a load transient.

One of the parameters limiting the converter’s response to

a load transient is the time required to change the inductor

current. Given a sufficiently fast control loop design, the

ISL6526 will provide either 0% or 100% duty cycle in

response to a load transient. The response time is the time

required to slew the inductor current from an initial current

value to the transient current level. During this interval the

difference between the inductor current and the transient

current level must be supplied by the output capacitor.

Minimizing the response time can minimize the output

capacitance required.

The response time to a transient is different for the

application of load and the removal of load. The following

equations give the approximate response time interval for

application and removal of a transient load:

response time to the removal of load. The worst case

response time can be either at the application or removal of

load. Be sure to check both of these equations at the

minimum and maximum output levels for the worst case

response time.

Input Capacitor Selection

Use a mix of input bypass capacitors to control the voltage

overshoot across the MOSFETs. Use small ceramic

capacitors for high frequency decoupling and bulk capacitors

small ceramic capacitors physically close to the MOSFETs

The important parameters for the bulk input capacitor are the

voltage rating and the RMS current rating. For reliable

operation, select the bulk capacitor with voltage and current

ratings above the maximum input voltage and largest RMS

current required by the circuit. The capacitor voltage rating

should be at least 1.25 times greater than the maximum

input voltage and a voltage rating of 1.5 times is a

conservative guideline. The RMS current rating requirement

for the input capacitor of a buck regulator is approximately

1/2 the DC load current.

×

------------------------------------ 1.5

×

=

∆I=

x

ISL6526