 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
ISL8101 Datasheet(PDF) 6 Page - Intersil Corporation |
|
||||||||||||||||||||||||||||||
ISL8101 Datasheet(HTML) 6 Page - Intersil Corporation |
|
|
6 / 20 page  6 FN9223.0 February 13, 2006 sources; the internal pull-up current decrease to 0 as the VID voltage approaches the internal pull-up voltage. All VID pins are compatible with external pull-up voltages not exceeding the IC’s bias voltage. DACSEL/VID5 (Pin 3) If VRM10 pin is grounded, DACSEL/VID5 represents the 6th voltage identification input from the VRM10-compliant microprocessor, otherwise known as VID5. If VRM10 pin is open or pulled high, DACSEL/VID5 selects the compliance standard for the internal DAC: pulled to ground it encodes the DAC with AMD Hammer VID codes, while left open or pulled high, it encodes the DAC with Intel VRM9.0 codes. VRM10 (Pin 4) This pin selects VRM10.0 DAC compliance when grounded. Left open, it allows selection of either VRM9.0 or Hammer DAC compliance via DACSEL pin. ENLL (Pin 21) This pin is a precision-threshold (approximately 0.6V) enable pin. Held low, this pin disables controller operation. Pulled high, the pin enables the controller for operation. FB and COMP (Pins 6, 5) The internal error amplifier’s inverting input and output respectively. These pins are connected to the external network used to compensate the regulator’s feedback loop. An internal current source injects the offset (OFS) current sampled into the FB pin. Pulling COMP to ground through an impedance lower than 15 Ω disables the controller (same effect as ENLL pulled low). ISEN (Pin 7) This pin is used to close the current-balance loop and set the overcurrent protection threshold. A resistor connected between this pin and VCC has a voltage drop forced across it equal to that sampled across the lower MOSFET’s rDS(ON) during approximately the middle of its conduction interval. The resulting current through this resistor is used for channel current balancing and overcurrent protection. The voltage across the RISEN resistor is time multiplexed between the two channels. Use the following equation to select the proper RISEN resistor: where: rDS(ON)MAX = lower MOSFET’s highest drain-source ON resistance ( Ω; include temperature effects) IOUT = channel maximum output current (A) Read Channel Balance Current Loop paragraph for more information. UGATE1, 2 (Pins 19, 12) Connect these pins to the upper MOSFETs’ gates. These pins are used to control the upper MOSFETs and are monitored for shoot-through prevention purposes. Maximum individual channel duty cycle is limited to 66%. BOOT1, 2 (Pins 20, 11) These pins provide the bias voltage for the upper MOSFETs’ drives. Connect these pins to appropriately-chosen external bootstrap capacitors. Internal bootstrap diodes connected to the PVCC pins provide the necessary bootstrap charge. PHASE1, 2 (Pins 18, 13) Connect these pins to the sources of the upper MOSFETs. These pins are the return path for the upper MOSFETs’ drives. LGATE1, 2 (Pins 17, 15) These pins are used to control the lower MOSFETs and are monitored for shoot-through prevention purposes. Connect these pins to the lower MOSFETs’ gates. OFS (Pin 9) This pin is used to create an adjustable output voltage offset. For no offset, leave this pin open. For negative offset, connect a R’OFS resistor from this pin to VCC and size it according to the following equation: where: VOFFSET = desired output voltage offset magnitude (mV) For positive output voltage offset, connect a ROFS resistor from this pin to GND, sizing it according to the following equation: For more information, refer to the ‘Output Voltage Offset Programming’ paragraph. SSEND (Pin 10) This pin is an end of Soft-Start (SS) indicator; open drain output device stays ON during soft-start, and goes open when soft-start ends. RISEN rDS ON ()MAX IOUT × 95 µA ------------------------------------------------------- = R ′ OFS R1 1500 VOFFSET -------------------------- × = ROFS R1 500 VOFFSET -------------------------- × = ISL8101 ISL8101 |
Similar Part No. - ISL8101 |
|
Similar Description - ISL8101 |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
