 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
NQ12010SMA16PSS Datasheet(PDF) 11 Page - SynQor Worldwide Headquarters |
|
||||||||||||||||||||||||||||||
NQ12010SMA16PSS Datasheet(HTML) 11 Page - SynQor Worldwide Headquarters |
|
|
11 / 15 page  Product # NQ12T50SMA16 Phone 1-888-567-9596 Doc.# 005-2NS12TE Rev. A 5/28/04 Page 11 Technical Specification 9.6 - 14.4Vin 16A Non-Isolated Non-Isolated SMT Converter SMT Converter there is also no concern with operation or startup into large capacitive loads. The voltage may rise slowly while charging the output capacitance, but it will rise. There are also no problems starting into a load that has a resis- tive V-I curve. As long as the load draws less than the current limit value at 1/2 of the unit's setpoint voltage, proper startup is ensured. Internal Over-Voltage Protection: To fully protect from excessive output voltage, the NQ12 series contains two levels of Output Over-Voltage Shutdown circuitry. The first type monitors the output at the load via the Sense+ pin (or the output if Sense+ is left open). If the sensed voltage exceeds the (optionally trimmed) setpoint by ~10% this protec- tive circuit asserts the converter's low-side switch until the out- put returns to normal. This circuit tracks the trimmed setpoint; the +10% threshold is maintained over the wide trim range of the T50 model. This circuit can also be benignly activated dur- ing the response to a large, fast drop in load current. In this instance the converter's normal transient response is momen- tarily overridden by this OVP. The result is a slight asymmetry in the converter's observed transient response. It should be noted that there is no limit on this OVP; if a pow- erful external source attempts to raise the output of an NQ12 converter beyond 110% of its setpoint, the converter will sacri- fice itself trying to draw down that external source and protect its load from the overvoltage. The second Output Over-Voltage Shutdown circuit indepen- dently compares the voltage at the converter's output pin with that of a redundant reference. If the output ever exceeds ~125% of nominal setpoint, both converter switches are dis- abled. After the output voltage returns to normal, a softstart cycle is initiated. This OVP is independent of the trimmed setpoint. As such, the converter's load is protected from faults in the external trim cir- cuitry (such as a trim pin shorted to ground). Since the setpoint of this OVP does not track trim, it is set at 125% of 5.0V, or 6.2V, in the wide-trim T50 model. Over-Temperature Shutdown: A temperature sensor on the converter senses the average temperature of the module. The thermal shutdown circuit is designed to turn the converter off when the temperature at the sensed location reaches the Over-Temperature Shutdown value. It will allow the converter to turn on again when the temperature of the sensed location falls by the amount of the Over-Temperature Shutdown Restart Hysteresis value. APPLICATION CONSIDERATIONS Input Filtering/Capacitance/Damping: The filter circuit of Figure C is often added to the converter's input to prevent switching noise from reaching the input voltage bus. In the SMA16 (surface mount) converters Cin = 30µF and in the VMA16 (SIP) converters Cin = 45µF of high quality ceramic capacitors. With Lin of 1µH, Cd should be 100-200µF and Rd should be 0.1-0.2W, in most applications. For more informa- tion on designing the input filter and choosing proper values, contact SynQor technical support. With the values listed above, the ripple current in L1 will be below 100mA RMS for all units. The full-load worst-case filter operation is summarized in Table 1. Adding significant external pure ceramic capacitance directly across the converter's input pins is not recommended. Parasitic inductance associated with the input pin geometry and PCB traces can create a high-Q CLC circuit with any external capac- itors. Just a few nano-Henries of parasitic inductance can cre- ate a resonance (or an overtone) near the converter's switching frequency. Cin has a reactance of 10-20mW at the 330kHz switching frequency. To avoid this high-frequency resonance, any external input filter should exhibit a net source impedance of at least 20mW resistive through this frequency range. This requirement is easily met with the damping elements discussed above. Adding a small amount (a few µF) of high-frequency external ceramic will not violate it. If using converters at higher powers, do consider the ripple cur- rent rating of Cd. Contact SynQor technical support for more Figure C: NQ12 converter with Input Filter Vout Model Current (A RMS) Ripple (V RMS) Current in L1 (mA RMS) Vp Ripple (V RMS) Current in L1 (mA RMS) 0.9 5.2 0.06 32 0.04 21 1.0 5.5 0.07 34 0.04 22 1.2 6.0 0.08 40 0.05 27 1.5 6.7 0.09 47 0.06 31 1.8 7.4 0.11 54 0.07 36 2.0 7.8 0.11 59 0.08 39 2.5 8.8 0.13 69 0.09 46 3.3 10.4 0.15 81 0.10 54 5.0 12.3 0.16 86 0.11 57 Table 1: Full Load Input Filter Performance, SMA16 |
Similar Part No. - NQ12010SMA16PSS |
|
Similar Description - NQ12010SMA16PSS |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
